Honeywell HERMetic UTImeter Gtex Chem IIC User Manual

Honeywell HERMetic UTImeter Gtex Chem IIC

83 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

50489/GTEX Chem IIC/1805 1 UTImeter Gtex Chem IIC

Operation and Service Manual

for HERMetic UTImeter Gtex Chem IIC

for use in corrosive and non corrosive liquids

Portable Gas Tight Electronic Gauging Device

Ullage - Temperature - Interface detector

Note 1: to identify the unit

refer to section 2

Note 2: before using the

instrument please

read this book.

This document is subject to changes without notice.

Check updates on www.tanksystem.com or contact us at tanksystem@honeywell.com

Table of Contents

Questions and Answers:

R
robert94Aug 11, 2025
How to fix a Honeywell Measuring Instruments unit that does not switch on?
- K
  Katherine OwensAug 11, 2025
  If your Honeywell Measuring Instruments unit isn't switching on, the issue might stem from several causes. First, the battery could be too low, so try changing it. Alternatively, there might be corrosion on the battery or display unit terminals; cleaning them could resolve the problem. Lastly, the switch itself might be defective, in which case you should replace the display unit.
S
Sean MclaughlinAug 18, 2025
Why does my Honeywell HERMetic UTImeter Gtex Chem IIC Measuring Instruments show 'battery' and beep continuously?
- R
  Randy VasquezAug 18, 2025
  If your Honeywell Measuring Instruments unit displays a 'battery' message and the buzzer is constantly sounding, it's likely that the battery is too low. Replacing the battery should resolve this issue.
S
Stephanie FrankAug 23, 2025
What to do if my Honeywell HERMetic UTImeter Gtex Chem IIC Measuring Instruments displays 'No Msg'?
- J
  Joseph WilsonAug 23, 2025
  If your Honeywell Measuring Instruments displays 'No Msg', it indicates that either the sensor or the tape is not working. To resolve this, you should renew the sensor or renew the tape.
J
James MillerAug 29, 2025
What does 'Invalid' mean on my Honeywell HERMetic UTImeter Gtex Chem IIC display?
- E
  Erika PachecoAug 29, 2025
  If your Honeywell Measuring Instruments displays 'Invalid', it means the sensor is not working correctly. You should renew the sensor to fix this problem.
D
David CoxSep 4, 2025
Why does my Honeywell HERMetic UTImeter Gtex Chem IIC show 'Unknown'?
- L
  Larry BrownSep 4, 2025
  If your Honeywell Measuring Instruments displays 'Unknown', this indicates that the sensor is not working. Renewing the sensor should solve the problem.

Honeywell HERMetic UTImeter Gtex Chem IIC Specifications

General

Accuracy	±2% of reading
Temperature range	-20°C to +50°C
Tape Length	30m
Tape Material	stainless steel
Approvals	ATEX, IECEx
Gas Tightness	Yes
Measures	Ullage, Temperature, Interface
Measurement Range	Up to 30 m (98.4 ft)
Operating Temperature	-20°C to +50°C
Humidity Range	0% to 95% non-condensing
Power Supply	Rechargeable battery
Battery Life	Up to 12 hours
Certification	ATEX

Related product manuals

Preview: HERMetic UTImeter Gtex Chem

HERMetic UTImeter Gtex Chem

Preview: Honeywell HEN04112

Honeywell HEN04112

Honeywell HEN16142

Honeywell HEN04102

Honeywell HEN16162

Honeywell HEN16102

Preview: Honeywell Chadwick-Helmuth 8500C

Honeywell Chadwick-Helmuth 8500C

Chadwick-Helmuth 8500C+

Preview: Honeywell H Series

Honeywell H Series

Preview: Honeywell KA 54

Honeywell KA 54

Preview: Honeywell AS302P

Honeywell AS302P

Preview: Honeywell ENCAL 3000

Honeywell ENCAL 3000