Honeywell HERMetic UTImeter Gtex Chem User Manual (English)

Questions and Answers:

J
Jacqueline JohnstonAug 16, 2025
How to fix a Honeywell HERMetic UTImeter Gtex Chem Measuring Instruments unit that does not switch on?
- V
  Vincent GonzalezAug 16, 2025
  If your Honeywell Measuring Instruments unit doesn't switch on, there are several potential causes. First, the battery might be too low, so try changing it. Second, check for corrosion on the battery terminals and clean them if necessary. Third, inspect the display unit terminals for corrosion and clean them. Finally, the switch itself might be defective, requiring you to change the display unit.
V
vhowellAug 18, 2025
What to do if the buzzer doesn't beep on my Honeywell HERMetic UTImeter Gtex Chem?
- T
  tina47Aug 19, 2025
  If the buzzer on your Honeywell Measuring Instruments unit doesn't beep when switched on, there could be a few reasons. First, the buzzer might be switched off; try pressing the '-' button to reactivate it. Second, the keypad could be defective, or the buzzer itself may be faulty. In either of these cases, you'll need to change the display unit.
A
amberzimmermanAug 21, 2025
Why does my Honeywell HERMetic UTImeter Gtex Chem Measuring Instruments show 'battery' and beep continuously?
- S
  Susan RayAug 21, 2025
  If your Honeywell Measuring Instruments unit switches on but displays the message “battery” and the buzzer tones continuously, it indicates that the battery is likely too low. The solution is to change the battery.
M
millerjosephAug 25, 2025
Why doesn't the temperature stabilize on my Honeywell Measuring Instruments?
- R
  Rodney HarrisAug 26, 2025
  If the temperature reading on your Honeywell Measuring Instruments unit doesn't stabilize, there are a couple of things to check. If you're measuring a heated viscous liquid like heavy crude oil, check the stability in cold and hot water; if it's OK, the problem is with the liquid, not the probe. Alternatively, the sensing probe might be contaminated. Clean the temperature electrode, remove any residues or sludge, and then check the stability in cold and hot water.
T
Tammie HudsonAug 28, 2025
Why does Honeywell HERMetic UTImeter Gtex Chem Measuring Instruments always give water signal?
- T
  Terry MitchellAug 28, 2025
  If your Honeywell Measuring Instruments buzzer gives a water signal regardless of the liquid being gauged, it's likely that the sensing head is contaminated by conductive residues. You should wash, clean, and brush the sensing head with a soft brush, or consider changing the sensor.
A
Aaron RobinsonAug 30, 2025
Why does the Honeywell Measuring Instruments buzzer keep beeping?
- S
  Seth EvansAug 30, 2025
  If the buzzer on your Honeywell Measuring Instruments unit tones continuously when the sensing probe is in air, liquid, or water, it's likely that the battery is too low. Try changing the battery.
M
Megan KingSep 3, 2025
Why does Honeywell HERMetic UTImeter Gtex Chem Measuring Instruments give oil signal in water?
- M
  Michelle ObrienSep 3, 2025
  If your Honeywell Measuring Instruments unit gives an oil signal when it's in water, the sensing head may be contaminated by non-conductive residues. Try washing, cleaning, and brushing the sensing head with a soft brush, or consider changing the sensor.
J
Joe McdanielSep 5, 2025
What does 'No Msg' mean on Honeywell HERMetic UTImeter Gtex Chem Measuring Instruments?
- C
  Christopher HicksSep 5, 2025
  If your Honeywell Measuring Instruments displays “No Msg “, it indicates that either the sensor or the tape is out of order. You should renew the sensor or the tape.
A
Alexis GardnerSep 8, 2025
What does 'Invalid' mean on Honeywell HERMetic UTImeter Gtex Chem?
- B
  Brian RussellSep 8, 2025
  If your Honeywell Measuring Instruments displays “Invalid”, it indicates that the sensor is out of order. You should renew the sensor.
T
Trevor ShortSep 12, 2025
What does 'Unknown' mean on Honeywell Measuring Instruments?
- A
  Angelica NavarroSep 12, 2025
  If your Honeywell Measuring Instruments displays “Unknown”, it indicates that the sensor is out of order. You should renew the sensor.