Honeywell Series 3000 MkII - Menu Mode Operations

25
SERIES 3000 MKII TECHNICAL MANUAL S3KMKIIMAN_MAN0878_Issue 5_07/2013
12.1 Menu mode operation table
Menu mode allows the user to perform calibration and congure parameters such as full scale range, calibration gas level, calibration interval, inhibit current & timeout and set a password. To activate menu mode hold the
magnet over the MENU/ENTER switch for at least 5 seconds and then remove. Menu mode can be password protected to prevent unauthorized person from changing parameters. Initially the password is set to ‘000’ meaning
it is disabled. While in menu mode, the output current of the detector is inhibited to prevent false alarms.
Use the table below to help navigate the menus and make conguration changes. The menus are shown in the left hand column. Use ▲▼ to select the required menu and ‘’ to enter. Follow the information and instructions in
the table from left to right from the required menu.
1 Refer to section 8.2 for detailed zero and span calibration procedures. A detector tted with an oxygen sensor will skip the zeroing procedure. Re-calibrate the detector if left un-powered for periods in excess of 24 hours.
2 The calibration due warning counter is automatically reset after a successful calibration.
3 To exit the Change Sensor Menu without changing the sensor, use ‘’.
▲▼ OK ▲▼ OK ▲▼ OK ▲▼ OK ▲▼
SEt CAL
1

GAS READING, ‘ZEro’ AND FLASHING ‘
’
ICON DISPLAYED. APPLY ZERO GAS AND
USE ‘’ WHEN READING IS STABLE. ‘ZEro
PASS’ DISPLAYED IF OK, FAULT CODE
AND RETURNS TO MENU IF NOT. ‘
‘SPAN YES’ DISPLAYED TO ASK IF
YOU NOW WANT TO PERFORM SPAN
CALIBRATION. USE ‘’ TO PROCEED OR
USE ▲▼ TO SELECT ‘No’ AND RETURN
TO MENU MODE.

CURRENT SPAN CALIBRATION
FLASHING. USE ▲▼ TO CHANGE AND ‘’
TO CONFIRM. NEW SPAN CALIBRATION
POINT DISPLAYED WITH ‘YES’ FLASHING.
USE ‘’ TO CONFIRM (OR ▲▼ TO
SELECT ‘No’ AND RETURN TO SELECT
NEW VALUE).

GAS READING, ‘SPAn’ AND FLASHING
‘
’ ICON DISPLAYED. APPLY SPAN GAS AND
USE ‘’ WHEN READING STABLE. IF OK
‘PASS’ & ‘PurG’ DISPLAYED (IF FAIL ‘SPAN
FAIL’ DISPLAYED AND RETURNS TO MENU).
REMOVE SPAN GAS. WHEN READING <50%
OF SPAN POINT, COUNTDOWN BEGINS &
UNIT RETURNS TO MENU MODE.
SEt rAn9

‘rAn9’ DISPLAYED & CURRENT RANGE
FLASHES. USE ▲▼ TO SELECT
DIFFERENT RANGE (SEE SECTION 8.1
FOR AVAILABLE RANGES).

NEW RANGE DISPLAYED. ‘YES’ FLASHES.
USE ‘’ TO CONFIRM (OR ▲▼ TO
SELECT ‘no’ AND RETURN TO STEP 1).

UNIT RETURNS TO MENU MODE.
ConF
Inhb

‘Curr’ DISPLAYED WITH ‘
’ ICON.
CURRENT INHIBIT mA VALUE FLASHES.
USE▲▼ TO SELECT NEW VALUE (3 OR
4mA TOXICS, OR 3 OR 17.4mA OXYGEN
VERSION).

‘tImE’ DISPLAYED WITH ‘ ’ ICON.
CURRENT INHIBIT TIMEOUT PERIOD
(MINUTES) FLASHES. USE ▲▼ TO SET
NEW TIMEOUT. (IF SET TO 000 OUTPUT
IS PERMANENTLY INHIBITED).

NEW TIMEOUT DISPLAYED. ‘YES’
FLASHES. USE ‘’ TO CONFIRM (OR ▲▼
TO SELECT ‘no’ AND RETURN TO SELECT
NEW VALUE).

UNIT RETURNS TO MENU MODE
SEt
PASS

‘PASS’ DISPLAYED WITH FIRST DIGIT
OF THE PASSCODE FLASHING. USE ▲
TO SELECT 1ST DIGIT OF CURRENT
PASSWORD. USE ▼ TO MOVE TO NEXT
DIGIT AND SET REST OF PASSCODE.

NEW PASSCODE DISPLAYED WITH ‘YES’
FLASHING. USE ‘’ TO CONFIRM (OR ▲▼
TO SELECT ‘No’ AND RETURN TO SELECT
NEW VALUE).

UNIT RETURNS TO MENU MODE
CAL
Int
2

Int’ DISPLAYED WITH CURRENT
CALIBRATION INTERVAL FLASHING.
USE ▲▼ TO CHANGE INTERVAL.

NEW INTERVAL DISPLAYED WITH ‘YES’
FLASHING. USE ‘’ TO CONFIRM (OR ▲▼
TO SELECT ‘no’ AND RETURN TO SELECT
NEW INTERVAL).

‘duE’ DISPLAYED WITH ‘No’, ‘LCD’ OR
‘both’ FLASHING. USE ▲▼ TO SELECT
REQUIRED CAL DUE WARNING OUTPUT.

UNIT RETURNS TO MENU MODE
bumP
tESt

CURRENT GAS CONCENTRATION DISPLAYED
WITH OUTPUT INHIBITED ‘
’ ICON FLASHING.
APPLY BUMP TEST GAS AND CHECK PEAK
READING ON DISPLAY.

REMOVE GAS. FALLING REAL TIME GAS
READING DISPLAYED.

UNIT RETURNS TO MENU MODE
ForC
Curr

Curr’ DISPLAYED WITH ‘
’ ICON. DEFAULT
FORCE CURRENT ‘4.00’ FLASHES. USE ▲▼
TO CHANGE TO REQUIRED MA LEVEL.

UNIT RETURNS TO MENU MODE
CHAn
SEnS
3

‘SENS’ DISPLAYED. REMOVE SENSOR. FIT
NEW SENSOR. DISPLAY SHOWS ‘LOAd
SENS’. ‘SAmE GAS’ DISPLAYED (‘NEW GAS’
IF DIFFERENT GAS TYPE SENSOR FITTED)
THEN ‘WArm’ COUNT DOWN.
UNIT RETURNS TO MENU MODE
9u It

QUITS MENU MODE AND RETURNS TO
MONITORING MODE.