Honeywell VISTA-15P - Bypassing Protection Zones

VISTA-15P/20P/SIA Installation and Setup Guide
18
System Communication and Operation (Continued)
Keypad Functions
The following is a brief list of system commands. For detailed information concerning system functions, refer to
the User's Manual. For Touch Screen style keypad users, refer to the separate Touch Screen keypad (AUI)
User’s Guide.
Voice Keypads
The 6150V/6160V Voice Keypads provide the following features:
 Message Center, which lets the user record and playback one message.
 Voice Status, which can announce system status by using the STATUS key.
 Voice Chime, which can alert users to the opening of doors/windows while the system is disarmed.
Refer to the User Guide for specific procedures for activating and using these features.
Keypad Commands
Function
Description
Silence Burglary Alarms
Pressing any key will silence the keypad sounder for 10 seconds. Disarming the system
(security code + OFF) silences both keypad and external sounders.
Silence Fire or Carbon
Monoxide Alarms
Press the OFF [1] key to silence the keypad sounder and, for fire alarms, the external sounder.
The detector sounding stops when the contaminated air is cleared from the detector; see the
detector’s instructions for further information.
Quick Arm
If enabled (field 21), you can press [#] in place of the system's security code, plus the desired
arming key (Away, Stay, Instant, Maximum)
Single-Button arming
If programmed (*57 Function Key menu mode), lettered keys A-D can be used for arming, using
options 3-AWAY, 4-STAY, 5-NIGHT-STAY, or 6-Step-Arming
If used, no security code is required to arm the system.
Alarm Memory
When the system is disarmed, any zones that were in an alarm condition during the armed
period will be displayed. To clear this display, simply repeat the disarm sequence (enter the
security code and press the OFF key) again.
Arming Away
Enter code + AWAY [2] or simply press appropriate lettered key on the keypads (see “Single-
Button Arming” above). If the “Auto-Stay Arm” feature is enabled (field *84) and the entry/exit
door is not opened and closed within the programmed exit delay time, the system will
automatically arm in STAY mode if armed from a wired keypad (non-RF device). If the door is
opened and closed within the exit delay period, the system arms in AWAY mode.
Arming Stay
Enter code + STAY [3] or simply press appropriate key on the keypads (see “Single-Button
Arming” above). See “Arming Away” above for Auto-Stay arming feature.
Arming Night-Stay
Enter code + STAY [3] + STAY [3] or simply press appropriate key on the keypads (see “Single-
Button Arming” above).
Arming Instant
Enter code + INSTANT [7].
Arming Maximum
Enter code + MAXIMUM [4] or simply press appropriate lettered key on the keypads (see
“Single-Button Arming” above).
Disarming
Enter code + OFF [1]. If entry delay or an alarm is active, you do not need to press OFF.
Bypassing Zones
Enter code + BYPASS [6] + zone number(s).
Forced (Quick) Bypass
To automatically bypass all faulted zones, use the “Quick Bypass” method. Enter code +
BYPASS + [#], then wait for all open zones to be displayed. Arm when display indicates “ZONE
BYPASSED” and “READY TO ARM”.
Chime Mode
Enter code + CHIME [9]. To turn chime off, enter code + CHIME again.
Activate Output Devices
If relay outputs (via a 4204, or 4229) are used, two keypad entries available to the user are
included. If programmed, these entries can be used to manually activate or deactivate the
device(s) for starting or stopping some action, such as turning lights on or off, etc. These
keypad entries are:
[Security Code] + # + 7 + [2-digit Device #] activates (starts) that device.
[Security Code] + # + 8 + [2-digit Device #] deactivates (stops) that device.