EasyManua.ls Logo

HotSpring Aria - User Manual

HotSpring Aria
16 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
x Page x x
Pre-Delivery Instructions
Please take the time to read this booklet carefully, as it will provide you with the information you will need to ensure
the safe, secure, and timely installation of your new spa. The following sections are guidelines on how to prepare for
delivery and set-up of your new spa. Specifically covered are site selection, delivery access, ground preparation, and
electrical requirements.
Remember to carefully review the Owners Manual that accompanies your spa, and to register the spa's warranty
within 10 days of delivery. These items, along with other valuable information, will be found in the Owner’s Package
which has been placed in the equipment compartment of your spa, where you will also find its serial number.
Watkins Manufacturing Corporation reserves the right to change features, specifications and design without
notification and without incurring any obligation.
DATE PURCHASED: _________________________________________________________________
DATE INSTALLED: ___________________________________________________________________
DEALER: ___________________________________________________________________________
ADDRESS: __________________________________________________________________________
TELEPHONE: _______________________________________________________________________
In most cities and counties, permits will be required for the installation of electrical circuits or the construction of
exterior surfaces (decks and gazebos). In addition, some communities have adopted residential barrier codes which
may require fencing and/or self-closing gates on the property to prevent unsupervised access to a pool (or spa) by
children under 5 years of age. Your HOT SPRING spa is equipped with a locking cover that meets the ASTM F1346-
91 Standard for Safety Covers and as a result, is usually exempt from most barrier requirements. As a general
practice, your local Building Department will inform you of any applicable barrier requirements at the time a permit is
obtained for the installation of an electrical circuit. Your Hot Spring dealer can provide information on which permits
may be required.
Hot Spring Spa Pre-Delivery Instructions
Congratulations on your decision to enjoy the finest spa available...
Welcome to the growing family of HOT SPRING spa owners.
HIGHLIFE
®
COLLECTION
Register your warranty
using the QR code below:

Other manuals for HotSpring Aria

Questions and Answers

  • C
    Carolyn GarciaAug 20, 2025
    What to do if my HotSpring Aria Hot Tub is not heating up, but the jets and light are working?
    • A
      austinwilliamAug 20, 2025
      If your HotSpring Hot Tub isn't heating up, but the jets and light are working, with the Green logo "Ready" and Blue logo "Power" indicators blinking, it could be due to an open integrated pressure switch or a tripped circulation pump thermal cut-off. Here’s what you should do: * Check for clogged filters. The integrated pressure switch will reset when the flow of water through the heater has been restored. Call for service if the heater trips frequently. * Check for clogged filters or air locks in plumbing. Disconnect power to the spa and allow the circulation pump to cool. The circulation pump thermal cut-off will reset when the pump has cooled and power is reapplied. Call for service if the circulation pump thermal cut-off trips frequently.
  • A
    Anthony GarzaAug 22, 2025
    What to do if my HotSpring Hot Tub has a water odor?
    • P
      Peter MurphyAug 22, 2025
      If your HotSpring Hot Tub has a water odor, it could be due to excessive organics in the water, improper sanitization, or low pH. Here's what you can do: * Shock the spa with sanitizer. * Add sanitizer. * Adjust the pH to the recommended range.
  • W
    William WilliamsAug 25, 2025
    What to do if my HotSpring Hot Tub has a chlorine odor?
    • B
      Bonnie DavisAug 25, 2025
      If your HotSpring Hot Tub has a chlorine odor, it could be due to a high chloramine level or low pH. To fix this, shock the spa with sanitizer and adjust the pH to the recommended range.
  • O
    ochoareginaAug 26, 2025
    What to do if my HotSpring Hot Tub is inoperative?
    • D
      David MitchellAug 26, 2025
      If your entire HotSpring Hot Tub is inoperative, it could be due to a power failure, a tripped GFCI, a tripped heater high-limit thermostat, or the spa lock being activated. Here's what you can do: * Check the power source. * Reset the GFCI. If it won't reset, call for service. * Disconnect power for at least thirty seconds to reset the heater high limit. Check for clogged filters. If tripping continues, call for service. * Deactivate the spa lock.
  • D
    darrell49Aug 28, 2025
    What to do if my HotSpring Aria Hot Tub has algae growth?
    • K
      kirbydawnAug 28, 2025
      If you notice algae growth in your HotSpring Hot Tub, it's likely due to high pH or low sanitizer levels. You can address this by shocking the spa with sanitizer and adjusting the pH, and by shocking the spa with sanitizer and maintaining the sanitizer level.
  • R
    Robert Harmon Jr.Aug 30, 2025
    Why are the jets weak in my HotSpring Aria?
    • Y
      Yesenia YoderAug 30, 2025
      Weak or surging jets in your HotSpring Hot Tub can be caused by a low water level, clogged filters, or a closed Comfort Control lever. To fix this, add water, clean the filters, or open the Comfort Control lever.
  • J
    John BradyAug 31, 2025
    Why is the Green Logo "Ready" indicator blinking on my HotSpring Aria?
    • J
      James MoranAug 31, 2025
      If the Green Logo "Ready" indicator is blinking on your HotSpring Hot Tub, it indicates a temperature sensor problem. To resolve this, disconnect power for at least thirty seconds. If the blinking continues, call for service.
  • B
    Brian LeeSep 2, 2025
    Why is the Blue Logo "Power" indicator blinking on my HotSpring Hot Tub?
    • R
      Robert CampbellSep 2, 2025
      If the Blue Logo "Power" indicator is blinking on your HotSpring Hot Tub, it means the heater high-limit thermostat has tripped. To fix this, disconnect power for at least thirty seconds to reset the heater high limit. If it won't reset, check for clogged filters. If tripping continues, call for service.
  • N
    nbrooksSep 4, 2025
    What to do if my HotSpring Hot Tub light is inoperative?
    • H
      Hailey BeckerSep 4, 2025
      If the light in your HotSpring Hot Tub is inoperative, it could be due to the spa lock being activated or a faulty light wiring or assembly. To resolve this, deactivate the spa lock or replace the light assembly.
  • A
    alaneSep 6, 2025
    What to do if my HotSpring Aria Hot Tub water smells musty?
    • N
      nicholassullivanSep 6, 2025
      If your HotSpring Hot Tub has a musty odor, it's likely due to bacteria or algae growth. Shock the spa with sanitizer. If the problem is visible or persistent, drain, clean, and refill the spa.

HotSpring Aria Specifications

General IconGeneral
Water Care SystemFreshWater® Salt System
Lighting SystemLED lighting
Control SystemWireless remote control
Heater4, 000w/230v
Pump2 pumps
FiltrationTri-X filter
Warranty5 years equipment
Seating Capacity5-6

Related product manuals