How to prevent eye irritation in my HotSpring Hot Tub?
Eye irritation in your HotSpring Hot Tub can result from low pH or low sanitizer levels. Adjust the pH, shock the spa with sanitizer and maintain the sanitizer level.
What to do if my HotSpring HIGHLIFE ENVOY water smells bad?
If your HotSpring Hot Tub water has an odor, it could be due to excessive organics, improper sanitization, or low pH. To address this: * Shock the spa with sanitizer. * Add sanitizer. * Adjust the pH to the recommended range.
Why does my HotSpring HIGHLIFE ENVOY Hot Tub have a chlorine odor?
A chlorine odor in your HotSpring Hot Tub usually indicates a high chloramine level or low pH. Try these solutions: * Shock the spa with sanitizer. * Adjust the pH to the recommended range.
What to do if my HotSpring Hot Tub touchscreen continuously reads "Searching for spa"?
If the touchscreen on your HotSpring Hot Tub continuously reads "Searching for spa", it means the remote is not paired. Press the Jets button on the DOCK until the dock buttons flash, then press and hold the screen until Pairing Yes/No is displayed. Finally, press Yes to pair.
How to remove organic buildup or scum ring around my HotSpring Hot Tub?
An organic buildup or scum ring around your HotSpring Hot Tub is typically caused by a build-up of oils and dirt. Wipe off the scum with a clean rag. If the problem is severe, drain the spa, use a spa surface and tile cleaner to remove the scum, and then refill the spa.
What does it mean when the Blue Logo "Power" indicator is blinking on my HotSpring HIGHLIFE ENVOY?
If the Blue Logo "Power" indicator is blinking on your HotSpring Hot Tub, it indicates that the heater high-limit thermostat has tripped. To resolve this, disconnect power for at least thirty seconds to reset the heater high limit. If it doesn't reset, check for clogged filters.
How to get rid of musty odor in HotSpring HIGHLIFE ENVOY?
A musty odor in your HotSpring Hot Tub is usually caused by bacteria or algae growth. Shock the spa with sanitizer. If the problem is visible or persistent, drain, clean, and refill the spa.
How to remove stains from my HotSpring HIGHLIFE ENVOY Hot Tub?
Stains in your HotSpring Hot Tub can be caused by low total alkalinity and/or pH, or high iron or copper in the source water. To address this, adjust the total alkalinity and/or pH. You can also use a metal deposit inhibitor.
What does it mean when the Green Logo "Ready" indicator is blinking on my HotSpring Hot Tub?
If the Green Logo "Ready" indicator is blinking on your HotSpring Hot Tub, it indicates a temperature sensor problem. Disconnect power for at least thirty seconds. If blinking continues, call for service.
How do I fix scale buildup in my HotSpring HIGHLIFE ENVOY Hot Tub?
Scale buildup in your HotSpring Hot Tub is usually due to high calcium content in the water, along with high total alkalinity and pH. To resolve this: * Adjust the total alkalinity and pH. * If scale removal is required, drain the spa, scrub off the scale, refill it, and balance the water.
Crucial safety instructions that must be read and followed.
Safety guidelines to prevent child drowning and injury risks.
Precautions to prevent electrical shock hazards.
Dangers of prolonged immersion in hot water and symptoms of hyperthermia.
Step-by-step guide for initial spa setup and filling.
Guidelines for safe handling and use of spa chemicals.
Detailed steps for draining and refilling the spa.
Steps for removing and cleaning the spa filter cartridges.
Key considerations for choosing and preparing the spa's location.
Step-by-step guide for leveling the spa using shims.
Recommended ground preparation and foundation types for spa installation.
Troubleshooting power and heating issues related to RCDs/thermostats.
General troubleshooting guide for common spa problems.
Crucial safety instructions that must be read and followed.
Safety guidelines to prevent child drowning and injury risks.
Precautions to prevent electrical shock hazards.
Dangers of prolonged immersion in hot water and symptoms of hyperthermia.
Step-by-step guide for initial spa setup and filling.
Guidelines for safe handling and use of spa chemicals.
Detailed steps for draining and refilling the spa.
Steps for removing and cleaning the spa filter cartridges.
Key considerations for choosing and preparing the spa's location.
Step-by-step guide for leveling the spa using shims.
Recommended ground preparation and foundation types for spa installation.
Troubleshooting power and heating issues related to RCDs/thermostats.
General troubleshooting guide for common spa problems.
General| Seating Capacity | 5-6 |
|---|---|
| Jet Count | 43 |
| Pump | 2-speed |
| Filtration | Tri-X |
| Cabinet Material | Everwood HD™ |
| Control System | IQ 2020 |
| Lighting | LED |
| Warranty | 5-year shell warranty |
| Dimensions | 7'8" x 7'8" x 38" (234 cm x 234 cm x 97 cm) |
To Next Page
