EasyManuals Logo

HP 280 G1 User Manual

HP 280 G1
136 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #90 background imageLoading...
Page #90 background image
Table 7-1 Solving Hardware Installation Problems (continued)
A new device is not recognized as part of the system.
Cause Solution
To access Device Manager in Windows 7, click Start, select
Control Panel, and then select Device Manager.
To access Device Manager in Windows 8.1, from the Start screen,
type c, select Control Panel from the list of applications, and then
select Device Manager.
USB ports on the computer are disabled in Computer Setup. Run the Computer Setup utility and ensure that Device available
is selected for appropriate USB ports under Security > USB
Security.
Computer will not start.
Cause Solution
Wrong memory modules were used in the upgrade or memory
modules were installed in the wrong location.
1. Review the documentation that came with the system to
determine if you are using the correct memory modules and
to verify the proper installation.
NOTE: DIMM1 or XMM1 must always be installed. DIMM1
must be installed before DIMM2, and DIMM3 must be
installed before DIMM4.
2. Observe the beeps and LED lights on the front of the
computer. Beeps and flashing LEDs are codes for specific
problems.
3. If you still cannot resolve the issue, contact Customer
Support.
Power LED flashes Red five times, once every second, followed by a two second pause, and the computer beeps five times. (Beeps
stop after fifth iteration but LEDs continue flashing.)
Cause Solution
Memory is installed incorrectly or is bad. CAUTION: To avoid damage to the DIMMs or the system board,
you must unplug the computer power cord before attempting to
reseat, install, or remove a DIMM module.
1. Reseat DIMMs. Power on the system.
2. Replace DIMMs one at a time to isolate the faulty module.
NOTE: DIMM1 or XMM1 must always be installed. DIMM1
must be installed before DIMM2, and DIMM3 must be
installed before DIMM4
3. Replace third-party memory with HP memory.
4. Replace the system board.
82 Chapter 7 Troubleshooting without diagnostics

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the HP 280 G1 and is the answer not in the manual?

HP 280 G1 Specifications

General IconGeneral
Tcase72 °C
Bus typeDMI
SteppingC0
FSB ParityNo
Processor cache3 MB
Processor cores2
Processor modelG3250
System bus rate5 GT/s
Processor familyIntel Pentium G
Processor seriesIntel Pentium G3000 series for Desktop
Processor socketLGA 1150 (Socket H3)
Processor codenameHaswell
Number of QPI links0
Processor frequency3.2 GHz
Processor cache typeSmart Cache
Processor lithography22 nm
Processor manufacturerIntel
Processor front side bus- MHz
PCI Express slots version3.0
Processor operating modes64-bit
ECC supported by processorYes
PCI Express configurations1x16, 2x8, 1x8+2x4
Thermal Design Power (TDP)53 W
Number of processors installed1
Maximum number of PCI Express lanes16
Memory types supported by processorDDR3-SDRAM
Memory clock speeds supported by processor1333 MHz
Memory bandwidth supported by processor (max)21.3 GB/s
Maximum internal memory supported by processor32 GB
Operating system installedWindows 7 Professional
Chassis typeMicro Tower
Product colorBlack
Country of originChina
Memory slots2x DIMM
Internal memory4 GB
Memory channelsDual-channel
Memory clock speed1600 MHz
Maximum internal memory16 GB
Memory layout (slots x size)1 x 4 GB
HDD speed7200 RPM
HDD interfaceSATA
Storage mediaHDD
Optical drive typeDVD Super Multi
Card reader integrated-
Total storage capacity500 GB
Product typePC
Motherboard chipsetIntel® H81
Discrete graphics card modelNot available
On-board graphics card modelIntel® HD Graphics
Maximum on-board graphics card memory1.7 GB
On-board graphics card base frequency350 MHz
On-board graphics card DirectX version11.1
On-board graphics card dynamic frequency (max)1100 MHz
Number of displays supported (on-board graphics)3
Power supply180 W
Ethernet LAN data rates10, 1000, 100 Mbit/s
USB 2.0 ports quantity6
Scalability1S
Processor codeSR1K7
Processor ARK ID83538
Processor package size37.5 x 37.5 mm
Supported instruction setsSSE4.1, SSE4.2
Thermal solution specificationPCG 2013C
Intel Secure Key Technology version1.00
Intel Stable Image Platform Program (SIPP) version0.00
Weight and Dimensions IconWeight and Dimensions
Depth355 mm
Width165 mm
Height358.8 mm
Weight7050 g

Related product manuals