HP 8920B - Page 678

Index
678
COPY command, 372
copying files, 372
default file system, 346
EDIT mode - entering/exiting, 410
error messages, 643
GET command, 362
INITIALIZE command, 362, 370, 375,
376
initializing media, 362
language, 20
LOAD command, 362
making a simple measurement, 38
Mass Storage Volume Specifier (MSI),
370
MSI, 370
passing control back using PASS CON-
TROL, 337
program development (see Program
Development), 381
requesting HP-IB active control, 338
running programs, 30
SAVE command, 362
selecting mass storage devices, 356
STORE command, 362
storing files, 362
IEEE 488.1
compliance, 39, 40
Interface Function Capabilities, 40
Passing Control (see Passing Control),
334
Remote Interface Message Capabili-
ties, 42
SRQ (see Service Requests), 311
IEEE 488.2
Common Commands, 224
Common Commands CLS, 239
Common Commands ESE, 239, 281
Common Commands ESE?, 239, 280
Common Commands ESR?, 239, 278
Common Commands IDN, 225
Common Commands OPC, 233
Common Commands OPC?, 235
Common Commands OPT, 227
Common Commands PCB, 240, 336
Common Commands RCL, 241
Common Commands RST, 217, 230
Common Commands SAV, 241
Common Commands SRE, 240, 314
Common Commands SRE?, 240, 314
Common Commands STB?, 240, 264
Common Commands TRG, 240, 243
Common Commands TST, 231
Common Commands WAI, 238
Common CommandsRST, 328
compliance, 39, 40
Output Queue, 282
Overlapped commands, 62
Sequential commands, 62
Standard Event Status Register, 276
Status Byte Register, 262
Increasing measurement speed, 252
autoranging, 252
autotuning, 252
combining ENTER statements, 257
combining OUTPUT statements, 256
compound commands, 256
measurement setup time, 255
screen display time, 258
speed of control program, 256
Input Attenuator
Call configure screen, 622
instrument function
querying ON/OFF state, 81
turning ON and OFF, 80
Instrument Initialization, 321
Device Clear (DCL) HP-IB Bus Com-
mand, 331
Front panel PRESET key, 325
Interface Clear (IFC) HP-IB Bus Com-
mand, 333
methods of, 322
power on reset, 322
RST Common Command, 328
Selected Device Clear (SDC) HP-IB
Bus Command, 332
Integer Number Setting
HP-IB command syntax diagram, 190
Internal Automatic Control Mode, 20, 23
K
keys
front panel, 39
L
Library files, 453
backing up, 371
LIF file names, 359
LIF file system, 358
initializing media for, 362
lock up
HP-IB bus, 245, 250
M
Manual Control Mode, 19, 23
Mass Storage Devices, 345
accessing, 357
default locations, 355
EPSON cards, 353, 354, 365
external disk drives, 352, 376
initializing media for, 362, 370, 375
OTP card, 354, 365
overview, 348
PCMCIA cards, 353, 354, 366
RAM Disk, 350, 374
ROM card, 354, 365
ROM Disk, 350, 364
selecting, 356
SRAM card, 353, 365
write protecting, 367
Mass storage locations
default values, 355
selecting, 356
Mass Storage Volume Specifier, 370
Measure
HP-IB command syntax diagram, 163
measurement
active, 19, 33
querying ON/OFF state, 81
querying value, 19, 34, 66
recommended sequence, 30
turning ON and OFF, 80
Measurement speed - increasing (see In-
creasing Measurement Speed), 252
Memory Cards, 345
address, 370
battery (see Battery), 368
initializing, 362, 370
inserting, 366
Mass Storage Volume Specifier, 370
OTP cards, 354
part numbers, 365, 366
removing, 366
ROM cards, 354