EasyManua.ls Logo

HTP SSC-50 - User Manual

Default Icon
16 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Superstor
Contender
Indirect Fired Water Heaters
Installation
Start-Up
Maintenance
Parts
Warranty
For Residential and Commercial Use
SSC Models
This manual must only be used by a qualied installer / service technician. Read all instructions in this manual before installing.
Perform steps in the given order. Failure to do so could result in substantial property damage, severe personal injury, or death.
The manufacturer reserves the right to make product changes or updates without notice and will not be held liable for
typographical errors in literature.
The surfaces of these products contacted by potable (consumable) water contain less than 0.25% lead by weight as required by
the Safe Drinking Water Act, Section 1417.
NOTE TO CONSUMER: PLEASE KEEP ALL INSTRUCTIONS FOR FUTURE REFERENCE.
272 Duchaine Blvd New Bedford, MA 02745 www.htproducts.com
lp-65 Rev. 002 Rel. 010 Date 10.11.19

Table of Contents

Other manuals for HTP SSC-50

Preview: Installation Start-Up Maintenance Parts
Installation Start-Up Maintenance Parts20 pages
Preview: Installation Manual
Installation Manual16 pages

Questions and Answers

  • E
    erikspencerSep 8, 2025
    What to do if I have hot tubs, spas, multiple showers, or high demand with my HTP SSC-50?
    • C
      Courtney HarrisonSep 8, 2025
      If you're experiencing issues with hot tubs, spas, multiple showers, or high demand when using your HTP Water Heater, it could be due to several factors. The pressure might be too low, so check the line pressure for any restrictions. The tank recovery might be slow (slow startup boiler, see chart), or there might not be enough hot water (boiler sized too small, see chart). The demand might also be too great; in this case, check flow rates and compare them to the chart, and consider installing a mixing valve and/or flow restricting valve and raise the tank and boiler temperature.
  • G
    George LeeAug 23, 2025
    What to do if circulator is not operating in my HTP SSC-50 Water Heater?
    • M
      mprinceAug 23, 2025
      If the circulator is not operating, check or replace it.
  • J
    Jessica FreemanAug 25, 2025
    How to fix air trap in loop of my HTP SSC-50 Water Heater?
    • K
      Kathryn PhillipsAug 25, 2025
      To fix an air trap in the loop, purge the air.
  • S
    Samuel RodgersAug 27, 2025
    What to do if water expands when heated in my HTP SSC-50?
    • B
      Brooke KellyAug 27, 2025
      If water expands when heated, install an expansion tank.
  • C
    Curtis SinghAug 28, 2025
    What to do if zone valve fails in my HTP SSC-50 Water Heater?
    • S
      Scott JohnsonAug 28, 2025
      If the zone valve fails, replace the valve.
  • V
    Vincent MyersSep 22, 2025
    What to do if the zone valve is not opening on my HTP SSC-50 Water Heater?
    • T
      tiffanywillisSep 22, 2025
      If the zone valve is not opening on your HTP Water Heater, open it manually to replace it.
  • D
    Deborah HunterSep 16, 2025
    What to do if there is a circulator failure in my HTP SSC-50?
    • M
      melissa78Sep 16, 2025
      If there's a circulator failure in your HTP Water Heater, replace the circulator.
  • S
    skerrSep 18, 2025
    What to do if there is a zone valve failure in my HTP Water Heater?
    • S
      Sheila WalshSep 18, 2025
      If there's a zone valve failure in your HTP Water Heater, replace the valve.
  • J
    Joseph BrewerSep 7, 2025
    What to do if my HTP SSC-50 Water Heater has a rotten egg odor?
    • K
      Kylie CampbellSep 7, 2025
      If your HTP Water Heater smells like rotten eggs, it is likely due to the supply water having a high sulfate or mineral content. To address this, check with a water quality specialist in your area and have your water supply analyzed. Then, address any water quality issues according to the specialist’s recommendations.
  • J
    Jamie RiveraSep 4, 2025
    What to do if my HTP SSC-50 has no hot water?
    • T
      Timothy ReyesSep 4, 2025
      If your HTP Water Heater isn't producing any hot water, several factors could be the cause. These include a zone valve not opening (check or replace), a circulator not operating (check or replace), a tank control set too low (raise tank temperature), a boiler control set too low (raise boiler temperature), incorrect wiring (recheck wiring), a tank control failure (replace control), or an air trap in the loop (purge air).

Summary

General Safety Information

When Servicing the Water Heating System

Safety precautions for maintenance and servicing the system.

Water Temperature Adjustment

Safe temperature settings to prevent scalding and related risks.

Piping

Plumbing

Temperature and Pressure Relief Valve

Installation and function of the T&P relief valve.

Scalding

Risks and prevention of scalding from hot water.

Heater Control and Wiring

Control

Details on the surface-mounted control unit and its settings.

Wiring

Guidelines for safe and compliant electrical wiring procedures.

Wiring Diagrams

Start-Up and Operation

Maintenance and Troubleshooting

Troubleshooting Guide

Solutions for common operational problems and error conditions.

HTP SSC-50 Specifications

General IconGeneral
BrandHTP
ModelSSC-50
CategoryWater Heater
LanguageEnglish

Related product manuals