To Next PageTo Next Page
Need help?Do you have a question about the Huawei OptiX RTN 310 and is the answer not in the manual?
General| Brand | Huawei |
|---|---|
| Model | OptiX RTN 310 |
| Category | Wireless Access Point |
| Language | English |
Lists the main RTN 310 unit included in the package.
Details the bundled auxiliary materials for installation and operation.
Identifies the outdoor binding straps for cable management.
Lists waterproof labels for cable identification and management.
Lists engineering labels for indoor cable management and identification.
Specifies the waterproof tape used for sealing and protection.
Refers to the quick installation guide document itself.
Advises against working with electrical current during thunderstorms to prevent hazards.
Emphasizes following local safety guidelines during extreme weather installations.
Provides safety guidelines for personnel working at elevated locations.
Warns about avoiding exposure to harmful high-power radio frequency signals.
Advises against looking into optical ports without proper eye protection.
Highlights potential high surface temperatures and recommends protective gloves.
Outlines conditions that may require anti-corrosion measures for installation sites.
Provides guidelines for safely moving and hoisting heavy equipment.
Details how to protect equipment ports to ensure signal integrity and prevent damage.
Specifies time limits for powering on equipment after unpacking.
Mandates securing or covering unused Ethernet service ports to prevent hazards.
Warns about disabling PoE function when connecting non-RTN 310 devices to prevent damage.
Describes the physical appearance and various ports of the RTN 310 unit.
Details the appearance and ports of the hybrid coupler component.
Identifies and describes different types of cables used with the RTN 310.
Explains the function and features of the Indoor PI component.
Provides information on installing and using mounting brackets for the Indoor PI.
Details the use of USB flash drives for loading NE data and system configuration.
Step-by-step guide for terminating outdoor network cables with RJ45 connectors.
Lists the pin assignments and functions for the RTN 310 P&E port.
Instructions for terminating indoor PI power cables using EPC4 connectors.
Steps for terminating a PGND cable using an OT terminal.
Step-by-step guide for installing RTN 310 at a mobile backhaul edge with an indoor PI.
Steps for commissioning the installed RTN 310 at a mobile backhaul edge.
Step-by-step guide for installing RTN 310 at a mobile backhaul edge with an outdoor PI.
Steps for commissioning the installed RTN 310 at a mobile backhaul edge.
Instructions for installing RTN 310 co-sited with a dock.
Steps for commissioning the RTN 310 installed co-sited with a dock.
Guide for installing RTN 310 at a 2x(1+0) aggregation site.
Steps for commissioning the RTN 310 at an aggregation site.
Instructions for installing RTN 310 to work with an RTN 900.
Steps for commissioning the RTN 310 when working with an RTN 900.
Guide for installing RTN 310 at an XPIC site.
Steps for commissioning the RTN 310 at an XPIC site.
Guide for installing RTN 310 at a 1+1 LAG mode site.
Steps for commissioning the RTN 310 at a 1+1 LAG mode site.
Guide for installing RTN 310 at a 1+1 optical splitter mode site.
Steps for commissioning the RTN 310 at a 1+1 optical splitter mode site.
Discusses the relationship between RSSI voltage and receive signal level.
Provides instructions on how to waterproof ground clips using tape and straps.
Step-by-step guide for installing the waterproof socket for outdoor fiber optic cables.
Describes how to adjust antenna polarization direction for single and dual-polarized antennas.
Details the procedure for mounting the RTN 310 unit onto an antenna.
Explains the process of installing a hybrid coupler on the antenna.
Instructions for installing a split-mount bracket assembly onto a pole.
Procedure for attaching the RTN 310 to the split-mount bracket assembly.
Details the installation of flexible waveguides, including considerations for polarization and bending.
Describes the method for waterproofing flexible waveguides.
Lists the components included in the flexible waveguide fixing set.
Guides on how to install the flexible waveguide fixing set on a pole.
Explains how to secure the flexible waveguide using the fixing set and clamps.
Step-by-step guide for installing the PGND cable for the RTN 310.
Instructions for installing an outdoor fiber optic cable.
Procedure for installing a P&E cable for power and Ethernet services.
Guide for installing a GE cascade fiber optic cable.
Instructions for installing an XPIC cascade cable.
Procedure for installing a 1+1 cascade fiber optic cable.
Details on how to install a ground clip for grounding purposes.
Guidance on routing outdoor fiber and GE cables, including drip loops.
Identifies specific ground points for the RTN 310 and PI when installed outdoors.
Instructions for installing an Indoor PI within an ETSI cabinet.
Instructions for installing an Indoor PI within a standard 19-inch cabinet.
Step-by-step guide for mounting an Indoor PI directly onto a wall.
Instructions for installing an Indoor PI within an outdoor cabinet.
Guidance on routing indoor PI cables within a cabinet for proper management.
Procedure for opening the cover of an outdoor optical splitter.
Instructions for mounting an outdoor optical splitter onto a wall.
Instructions for mounting an outdoor optical splitter onto a pole.
Guidance on routing and securing optical fibers within the splitter enclosure.
Detailed steps for routing fibers, connecting adapters, and securing them.
Procedure for securely closing the cover of the outdoor optical splitter.
Identifies specific ground points for the RTN 310 and PI when installed outdoors.
A checklist for verifying the correct installation and condition of RTN 310 cables.
A checklist for verifying the secure and correct installation of the Indoor PI.
Steps for powering on the RTN 310 when supplied by an indoor PI.
Steps for powering on the RTN 310 when supplied by an outdoor PI.
Instructions for powering on the RTN 310 when it works with an RTN 900.
Guide on how to load network element data using a USB flash drive or Web LCT.
