Why Hunter Douglas PowerView Window Blinds raise from the sill?
A small gap between the sill and the bottom of the Hunter Douglas PowerView Window Blinds shading is normal when the vanes are fully lowered and closed. If this distance is excessive or changes over time, open the shading to its full 'vane open' position and try again.
Why is my Hunter Douglas Window Blinds shade hard to raise or lower?
If your Hunter Douglas Window Blinds shade is hard to raise or lower, or won't move at all, consider these potential issues: First, remember that shadings cannot be forced into tight inside mount window openings. If it's an inside mount, ensure the headrail is correctly installed and there's enough clearance between the ends of the shade and the window casement. Check that the installation brackets are level and aligned; adjust or shim if needed. If you have EasyRise™, make sure the cord tensioners are mounted correctly. For LiteRise®, close the vanes by pressing down on the front of the handle before raising or lowering.
Why is the bottom rail on my Hunter Douglas PowerView Window Blinds not raising or lowering completely?
If the bottom rail on your Hunter Douglas PowerView Window Blinds shade isn't raising or lowering completely, or its position has changed, the batteries in the battery wand or satellite battery pack may be low, so try replacing them. Also, make sure the battery wand, satellite battery pack, or 18V DC power supply is securely connected to the power cable, and that the cables aren't pinched or caught in the headrail or installation brackets.
What to do if Hunter Douglas PowerView Window Blinds shade is not responding to the remote?
If your Hunter Douglas PowerView Window Blinds shade isn't responding to the remote, first check that the correct group number is selected. Then, check that the batteries in the remote are correctly inserted and are fresh. The LEDs that backlight the remote should light up fully when you press STOP.
Why do Hunter Douglas Window Blinds raise unevenly?
If your Hunter Douglas Window Blinds raise or lower unevenly, the fabric rubs, or the bottom rail is uneven, check that the window is square by measuring the diagonals. Also, ensure the installation brackets are level, using shims if necessary. You can also adjust the bottom rail weight (though this doesn't apply to LiteRise® shadings).
What to do if Hunter Douglas PowerView Window Blinds shade doesn't work with the programming button?
If your Hunter Douglas PowerView Window Blinds shade isn't working with the programming button, try these steps: First, unplug the power cable from the motor, then plug it back in. A green LED inside the programming button housing should flash, indicating the motor has power. Next, check that the batteries in the battery wand or satellite battery pack are correctly inserted and fresh. Also, ensure that the battery wand, satellite battery pack, or 18V DC power supply is securely connected to the power cable and that the cables aren't pinched or caught in the headrail or installation brackets.
Why won't my Hunter Douglas LiteRise Indoor Furnishing shading snap into the brackets?
If your Hunter Douglas shading won't snap into the installation brackets, check that the brackets are aligned and level. Also, make sure the locking tab on the installation bracket slides over the headrail.
How to reattach tassel cord on Hunter Douglas LiteRise Indoor Furnishing UltraGlide shading?
To reattach the tassel cord on your Hunter Douglas UltraGlide shading, hook one side of the lower cord connector to the upper cord connector. Rotate the lower cord connector until it snaps into place. Twirl the tassel cord to remove any stray cord fibers from the junction of the cord connector halves, as these can cause the connector to come apart.
What to do if the Hunter Douglas LiteRise shade will not fit into the installation brackets?
If your Hunter Douglas Indoor Furnishing shade does not fit into the installation brackets, check that the installation brackets are level and aligned. Shim the installation brackets to level the headrail, if necessary. Be sure the heads of the screws are flush against the installation bracket and that the headrail is completely inserted into the installation brackets.
What to do if lift cords are bunching in Hunter Douglas Window Blinds?
If the lift cords are bunching by the safety cord connector in your Hunter Douglas Window Blinds, ensure the slats are in the open position. Then, raise and lower the blind to straighten the lift cords.
General| Suitable For | Residential, Commercial |
|---|---|
| Product Type | Window Shades and Blinds |
| Fabric Options | Variety of colors and materials |
| Mounting Options | Inside or outside mount |
| Safety | Child-safe operation |
To Next Page
