•
LCD temperature
: Measured by a temperature
sensor on the application circuit board.
4.4.1.5 Tools - Info - Automower
®
Connect
The
Automower
®
Connect
menu shows:
•
COM
: the version of the program on the
communication circuit board.
•
SIM card
:
•
OK
: Connected.
•
PIN
: SIM PIN is required.
•
PUK
: SIM PUK is required. To enter the PUK
code, insert the SIM card into a cell phone.
Note: You have to enter the PUK code when an
incorrect PIN code is entered too many times.
You can not enter the PUK code in the product.
•
Locked
: The SIM card is locked. The SIM card
is permanently locked and must be replaced.
Note: The SIM card is locked when an incorrect
PUK code is entered too many times.
•
Error
: Other fault.
•
-
: Automower
®
Connect is not active or no SIM
card is inserted.
•
GPRS
:
•
Ok
: The communication status with the app.
Note: The communication status must be
Ok
or
there is no communication with the app.
•
Error
: Not connected, no GRPS link.
•
Search
: Not connected, GPRS link ok.
•
Blocked
: The communication circuit board is
blocked. The serial number of the
communication circuit board is not registered on
Husqvarna server. Replace the communication
circuit board.
•
SIMs
: Data is not transmitted. Automower
®
Connect is attempting to transmit data but the
Husqvarna server is not receiving.
Note: If the SIM card is a cash SIM card and
there is no money left, this can cause the
SIMs
code.
•
PIN
: SIM PIN is required.
•
PUK
: SIM PUK is required. To enter the PUK
code, insert the SIM card into a cell phone.
Note: You have to enter the PUK code when an
incorrect PIN code is entered too many times.
You can not enter the PUK code in the product.
•
Locked
: The SIM card is locked. The SIM card
is permanently locked and must be replaced.
Note: The SIM card is locked when an incorrect
PUK code is entered too many times.
•
Error
: Other fault.
•
-
: Automower
®
Connect is not active or no SIM
card is inserted.
•
Data
: Data transmission
On/Off
.
•
SMS
: SMS function
On/Off
.
•
RSSI
: The signal strength of GPRS reception,
between 0-98. A higher the value means a better
reception. The value must be more than 10 for a
stable connection.
•
Carrier
: The name of the operator.
•
APN
: The APN used for the operator.
•
APN user
: User name for APN.
•
APN pwd
: Password for APN.
•
Geofence
: GPS coordinates for the center point for
the geofence
•
GPS signal
: The strength of the GPS reception. In
order to set the center position of the Geofence, the
GPS signal must be
Strong
.
4.4.1.6 Tools - Info - Motors
The
Tools - Info - Motors
menu has these sections:
•
Wheel motor
•
Cutting motor
•
Cut height
The
Info - Motors - Wheel motor
menu shows:
•
Speed
for the left/right wheel motor.
•
Current (mA)
for the left/right wheel motor.
•
Power (%)
for the left/right wheel motor.
The
Info - Motors - Cutting motor
menu shows:
•
Speed
of the cutting motor.
•
Current (mA)
for the cutting motor.
•
Average current (mA)
for the cutting motor.
The
Info - Motors - Cut height
menu shows:
•
Cutting height
: The blade disc height setting
measured in steps.
•
Current (mA)
for the cutting height motor.
4.4.1.7 Tools - Info - GPS navigation
The
Tools - Info - GPS navigation
shows:
•
Satellites
: The number of satellites the GPS
receiver is currently in contact with.
•
Position
: The products position in longitude and
latitude.
4.4.2 Tools - History, total
4.4.2.1 Tools - History, total - Key data
The Tools - History, total - Key data
menu shows:
•
Total running
: The total time in hours that the wheel
motors have been running.
Note:
Total running
also includes the time when the
product is running without mowing.
1582 - 001 - 23.12.2020 Special menus - 11
To Next Page
Loading...
Need help?
General
