D Command formats (Continued)
• Memory content
Command: 1A 00
0
X X X ∙∙∙∙∙∙ X X X X X X X X X X X 0 X X X X X XX X X XX X X X
X X X XX X
X X X XX XX X X XX X
X X ∙∙∙∙∙∙ X X ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ ∙∙∙∙∙∙X X X XX X ∙∙∙∙∙∙ X XX X ∙∙∙∙∙∙ X X
1 2, 3 4 , 5 ~ 9 ~
~ ~ ~ ~ 5 ~ ~
~ ~
q Frequency band setting
01 : 144 MHz frequency band
02 : 430 MHz frequency band
03 : 1.2 GHz frequency band
w, e Memory channel number
0001 ~ 0099: Memory channel 1 to 99
0100, 0101: Program Scan Edge channel 1A, 1B
0102, 0103: Program Scan Edge channel 2A, 2B
0104, 0105: Program Scan Edge channel 3A, 3B
0106, 0107: Call channel C1, C2
r Select memory setting
0X
e
0=OFF*
Fixed
1= 1
2= 2
3= 3
* For program scan edge channel, call channel,
set to “0.”
t ~ o Operating frequency setting
See “Operating frequency.” (p. 13)
!0, !1 Operating mode setting
See “Operating mode.” (p. 13)
!2 Data mode setting
1 byte data (XX)
00: Data mode OFF
01: Data mode ON
!3 Duplex and Tone settings
X X
0=Duplex OFF
1=
Duplex−
2=Duplex+
3=RPS*
0=OFF
1=TONE
2=TSQL
3=DTCS
* RPS can be set when DD mode is selected, and
DUP (+, -) can be set when other than DD mode is
selected.
!4 Digital squelch setting
X 0
!4
0=Digital squelch function OFF
1=Digital call sign squelch function ON (DSQL)
2=Digital code squelch function ON (CSQL)
Fixed
!5 ~ !7 Repeater tone frequency setting
!8 ~ @0 Tone squelch frequency setting
See “ Repeater tone/tone squelch frequency
setting.” (p. 19)
@1 ~ @3 DTCS code setting
See “ DTCS code and polarity setting.” (p. 19)
@4 DV Digital code squelch setting
See “DV Digital code squelch setting.” (p. 19)
@5 ~ @7 Duplex offset frequency setting
See “Duplex Offset frequency setting.” (p. 13)
@8 ~ #5 UR (Destination) call sign setting
(8 characters; xed)
#6 ~ $3 R1 (Access repeater) call sign setting
(8 characters; xed)
$4 ~ %1 R2 (Gateway/Link repeater) call sign setting
(8 characters; xed)
See “DV TX call signs setting.” (p. 19)
%2 ~ ^7 Memory name setting
(16 characters; xed)
See “Codes for character entries.” (p. 15)
To clear the memory channel contents on 1A 00:
w, e :Memory channel (0001~0099)
r : “FF,” t ~ :None
NOTE:
• The same data as t ~ %1 are stored in t ~ %1.
• When the Split function is ON, the data of t
~ %1 is
used for transmit.
• Even if the Split function is OFF, enter the data into t
~
%1 to match your transceiver. We recommend that you
set the same data as t
~ %1.
Remote control
14
To Next Page
Loading...
