Why can't I change the operating frequency on my Icom IC-A6E?
If you are unable to change the operating frequency or memory channel on your Icom Transceiver, the lock function may be activated. To deactivate it, push, then push [7• ].
What to do if Icom Transceiver operating frequency cannot be changed?
If you cannot change the operating frequency or memory channel on your Icom Transceiver, it's likely that the lock function is activated. To deactivate it, push, then push [7• ].
How to fix an Icom IC-A6E when no power comes on?
If your Icom Transceiver isn't powering on, there are several potential causes. First, the battery may be exhausted, so try recharging it. Second, there may be a bad connection with the battery pack, so check the connection to the transceiver. Finally, the CP-20’s fuse may be blown; in this case, identify the cause and replace the fuse.
Why is there no sound coming from the speaker of my Icom Transceiver?
If you're not hearing any sound from your Icom Transceiver's speaker, it could be due to a couple of reasons. The squelch level might be set too deep; try adjusting the squelch to the threshold point. Alternatively, the volume level might be too low; adjust the [VOL] to a suitable level.
What to do if my Icom Transceiver is not transmitting?
If your Icom Transceiver is not transmitting, there are two possible reasons. You may have the NAV band selected, if so, set COM band in frequency mode. Alternatively, the battery may be exhausted, so recharge the battery pack.
What to do if the scan does not start on my Icom IC-A6E?
If the scan function on your Icom Transceiver isn't starting, consider these potential causes: 1. Ensure that all memory channels in the selected bank are programmed as “TAG” channels, and if not, set the “TAG” settings of desired channels. 2. If the squelch is open, set the squelch level to tighten it. 3. If there are less than two memorized channels, program two or more memory channels.
How to turn on beep sounds on Icom IC-A6E?
If you are not hearing any beep sounds on your Icom Transceiver, the beep tones may be turned OFF. To turn them back on, push, then push [8•BEEP], and rotate [DIAL] to adjust the beep tone level.
Why Icom IC-A6E won't turn on?
Your Icom Transceiver might not be turning on due to several reasons. First, the battery might be exhausted, in which case you should recharge the battery pack. Another possibility is a bad connection for the battery pack; check the connection to the transceiver to ensure it's properly connected. Lastly, if you're using the CP-20, its fuse might be blown. Check for the cause and replace the fuse with a new one.
What to do if there is no sound from Icom Transceiver speaker?
If you're not getting any sound from your Icom Transceiver's speaker, it could be due to a couple of reasons. The squelch level might be set too deep; try setting the squelch to the threshold point. Alternatively, the volume level might be too low; adjust the [VOL] to a suitable level.
How to fix Icom IC-A6E Transceiver transmitting impossible issue?
If your Icom Transceiver is unable to transmit, there are a couple of things to check. If the NAV band is selected, set COM band in frequency mode. Also, ensure that the battery isn't exhausted by recharging the battery pack.
Introduction to the Icom IC-A24E/A6E VHF AIR BAND TRANSCEIVER.
Essential instructions for safe and proper operation of the transceiver.
Defines WARNING, CAUTION, and NOTE to ensure user understanding of safety and operational advice.
Critical safety and operational guidelines for handling and using the transceiver.
Overview and identification of controls and indicators for IC-A24E and IC-A6E models.
Detailed explanation of individual buttons and keys on the transceiver panel.
Explanation of keypad functions including CLEAR/DEL, ANL/SCAN, EMERGENCY, and POWER.
Usage of digit keys for inputting frequencies, selecting channels, and accessing secondary functions.
Explanation of indicators like F, TX, RX, DUP, LOW BATTERY, LOCK, and FREQUENCY DISPLAY.
Explanation of indicators like TAG, MEMORY, OVERFLOW, and COURSE indicators.
Core procedures for setting frequency, squelch, ANL, receiving, and transmitting.
How to select, transfer, program, name, and clear memory channels.
Procedures for COM band scan, memory scan, and TAG channel settings.
Detailed guide to VOR indicators, functions, flying, and crosschecking.
Setting up and operating the duplex function for communication with flight services.
Essential guidelines for charging, handling, and cautionary advice for battery packs.
Methods for cloning data between transceivers or from a PC, including error handling.
Solutions for common problems and guidance on CP-20 fuse replacement.
Detailed specifications for general, transmitter, and receiver functions.
Overview of available optional battery cases, chargers, clips, cables, and other items.
Guide to connecting an OPC-499 headset adapter and notes on headset compatibility.
Statement of compliance with EU directives and warning about licensing requirements.
General| Battery Life | Up to 12 hours |
|---|---|
| Weight | Approx. 240 g |
| Dimensions | 58 x 130 x 36 mm |
| Power Supply Requirement | 7.2 V DC |
| Antenna Impedance | 50 Ω |
| Output Power | 5W / 1W |
| Mode | AM |
| Channel Capacity | 200 channels |
| Channel Spacing | 25 kHz |
| Modulation System | AM |
| Spurious Emissions | -60 dB or better |
| Adjacent Channel Power | > 70 dB |
| Voltage | 7.2 V DC |
| Frequency Range | 118.000 - 136.9916 MHz |
| Audio Output Power | 0.5 W |
To Next Page
