How to unlock the frequency on my Icom IC-A15?
If you are unable to change the operating frequency or memory channel on your Icom Transceiver, the lock function may be activated. Push and hold [ ] for 2 seconds to turn the lock function OFF.
How to unlock Icom IC-A15 frequency?
If you're unable to change the operating frequency or memory channel on your Icom Transceiver, the lock function may be activated. Hold down [ ] for 2 seconds to turn the Lock function OFF.
How to fix an Icom IC-A15 that has no power?
If your Icom Transceiver won't turn on, the battery may be exhausted. Try recharging the battery pack. Alternatively, there might be a bad connection. Ensure the battery pack is properly connected to the transceiver.
Why is there no sound coming from my Icom IC-A15 Transceiver speaker?
If you can't hear any sound from the Icom Transceiver speaker, it might be due to the squelch level being too deep. Try setting the squelch to the threshold point. Also, the volume level might be too low. Adjust the [VOL] to a suitable level.
Why doesn't the scan start on my Icom IC-A15 Transceiver?
If the scan function on your Icom Transceiver does not start, it could be due to several reasons: * All memory channels in the selected bank are not programmed as “TAG” channels. Set the “TAG” settings of desired channels. * The squelch is open. Set the squelch level to tighten. * There are not more than 2 memorized channels. Program 2 or more memory channels.
How to turn on beep sounds on Icom IC-A15?
If there are no beep sounds on your Icom Transceiver, the beep tones may be turned OFF. To turn them ON: * For IC-A15: Push [FUNC], then push [BEEP](8). * For IC-A15S: Turn the beep tone ON in set mode.
How to fix Icom IC-A15 when no power comes on?
If your Icom Transceiver isn't powering on, the battery might be exhausted. Try recharging the battery pack or replacing the batteries. Also, ensure the battery pack has a good connection to the transceiver.
Why no sound from Icom Transceiver speaker?
If you're not getting any sound from the Icom Transceiver's speaker, the squelch level might be set too deep. Try setting the squelch to the threshold point. Alternatively, the volume level could be too low; adjust the [VOL] to a suitable level.
What to do if scan does not start on Icom IC-A15 Transceiver?
If the scan function isn't starting on your Icom Transceiver, there could be a few reasons: * Ensure that two or more memory channels in the selected bank are entered as 'TAG' channels; if not, set the 'TAG' settings of the channels. * The squelch might be open; try setting the squelch level to tighter. * Verify that two or more memory channels are entered; if not, enter at least two memory channels.
Why is transmitting impossible on my Icom Transceiver?
If you cannot transmit with your Icom Transceiver, the battery may be exhausted. Recharge the battery pack.
Crucial safety instructions for operation, handling, and potential hazards.
Overview of the transceiver's physical controls, buttons, and display elements.
Explains the purpose and usage of each key on the transceiver's keypad.
Interpretation of the icons and indicators shown on the transceiver's screen.
Instructions on how to select and input a desired operating frequency for the transceiver.
Guidance on how to receive signals and transmit audio using the transceiver.
How to configure side tone and monitor battery levels and low battery warnings.
Procedures for selecting, storing, and organizing frequencies in memory channels and banks.
Steps to save frequencies into memory and assign names for easier recall.
How to perform frequency scans and memory scans on the transceiver.
Using the TAG function to skip or include specific memory channels during scans.
Quick access method for the 121.5 MHz emergency frequency.
How to enable/disable the ANL function and set the key touch beep tone.
Guide to entering the Set mode and adjusting various transceiver settings.
Crucial safety warnings and guidelines for charging the transceiver's battery pack.
Detailed procedures for regular and rapid charging of battery packs using various chargers.
Instructions for attaching the battery case and installing alkaline batteries.
How to clone data between transceivers using a cable.
Cloning data to/from a PC and troubleshooting cloning errors.
A guide to identifying and resolving common issues encountered with the transceiver.
Detailed technical data including frequency range, power, and dimensions.
List of optional accessories such as battery packs, chargers, microphones, and cables.
Instructions for connecting and using an optional headset with the transceiver.
General| Number of Channels | 200 Channels |
|---|---|
| Modulation | AM |
| Channel Spacing | 25 kHz/8.33 kHz |
| Antenna Impedance | 50Ω |
| Spurious Emissions | Less than -60dBc |
| Adjacent Channel Selectivity | More than 70dB |
| Spurious Response Rejection | More than 70dB |
| Intermodulation Rejection | More than 70dB |
| Type | Handheld Transceiver |
| Frequency Range | 118.000 - 136.975 MHz |
| Power Output | 5W |
| Operating Voltage | 7.2 V DC |
| Current Drain (Transmit) | 1.5A |
| Squelch Sensitivity | Less than 0.5µV |
To Next Page
