How to unlock the frequency on my Icom IC-A24 Transceiver?
If you cannot change the operating frequency or memory channel, the lock function may be activated. To deactivate it, push [ ], then push [7• ].
How to unlock the channel selection on my Icom IC-A24 Transceiver?
If you cannot select the display channel on your Icom Transceiver, the lock function may be activated. To deactivate it, push, then push [7• ].
Why is there no sound coming from my Icom IC-A24 Transceiver speaker?
If no sound is coming from the speaker, the squelch level may be set too deep. Try setting the squelch to the threshold point. Alternatively, the volume level may be too low; adjust the [VOL] to a suitable level.
What to do if my Icom Transceiver won't turn on?
If your device isn't powering on, the battery may be exhausted; try recharging it. Also, check the battery pack connection to the transceiver to ensure it's secure. If you are using the CP-20, the fuse may be blown; check the cause and replace the fuse with a new one.
Why is transmitting impossible on my Icom IC-A24 Transceiver?
If you cannot transmit, it may be because WX channels or the NAV band is selected. Set the device to COM band in frequency mode. Alternatively, the battery may be exhausted; in this case, recharge the battery pack.
How to fix an Icom IC-A24 that won't turn on?
If your Icom Transceiver isn't powering on, it might be due to an exhausted battery. Try recharging the battery pack. Also, check the battery pack connection to the transceiver to ensure it's properly connected.
What to do if my Icom IC-A24 Transceiver is not transmitting?
If your Icom Transceiver won't transmit, it could be because you're on a receive-only channel. Try changing to a different channel. Also, ensure the battery is not exhausted by recharging it.
Why won't the scan start on my Icom Transceiver?
If the scan function on your Icom Transceiver doesn't start, it might be because not all memory channels are programmed as “TAG” channels. Set the “TAG” settings for the channels you want to include in the scan.
How to turn on beep sounds on my Icom Transceiver?
If your Icom Transceiver is not making any beep sounds, the beep tones may be turned off. To adjust the beep tone level, push, then push [8•BEEP].
How to fix Icom IC-A24 Transceiver when no power comes on?
If your Icom Transceiver isn't powering on, there are a couple of potential reasons. First, the battery might be completely drained, so try recharging the battery pack. Alternatively, there may be a bad connection with the battery pack. In this case, check the connection to the transceiver to ensure it's properly connected.
Covers critical safety instructions regarding battery, operation, environment, and FCC rules.
Describes the functions of the numeric and special digit keys.
Explains the primary functions of basic controls like LIGHT, PTT, VOL, DIAL, and ANT.
Step-by-step guide to setting frequencies using the keypad.
Instructions for setting frequencies using the tuning dial.
Guidelines for transmitting, including antenna use and microphone technique.
How to select memory channels using the tuning dial or keypad.
Step-by-step guide to storing frequencies into memory channels.
Details on how to program and display 6-character memory names.
Illustrates programming a frequency and name into memory channels.
How to assign custom 6-character names to memory channels.
Diagrams and explanations of VOR indicators in DVOR and CDI modes.
How to select and use CDI and DVOR modes for navigation.
How the IC-A24 displays deviation and guides flight to a VOR station.
Visual example of the aircraft being on course with VOR display.
How to set and follow a desired course using VOR navigation.
Step-by-step illustration of entering a desired course bearing.
How duplex function allows calling flight service while receiving VOR.
Visual example of the aircraft being off course with VOR display.
Method to determine location by cross-referencing two VOR stations.
Visual guide to crosschecking position using VOR stations.
Important safety warnings for handling and using battery packs.
Crucial safety information on RF exposure, duty cycle, and antenna placement.
Solutions for problems like no power or no sound from the speaker.
Troubleshooting for transmission failures and inability to change channels.
General| Channel Spacing | 25 kHz |
|---|---|
| Operating Voltage | 7.2 V DC |
| Mode | AM |
| Voltage | 7.2 V DC |
| Frequency Range | 118.000-136.975 MHz |
| Output Power | 5.0 W (PEP), 1.5 W (carrier) |
| Battery Life | 8 hours (with BP-210N) |
| Number of Memory Channels | 200 channels |
| Current Drain (Transmit) | 1.5 A |
| Modulation | AM |
| Number of Channels | 200 channels |
| Current Drain (Receive) | 300 mA (internal SP), 500 mA (external SP) |
To Next Page
