To Next PageTo Next PageHow to fix Icom Transceiver that does not turn on?
If your Icom Transceiver does not turn on, there could be a few reasons. First, the battery might be exhausted, in which case you should recharge it. Second, the battery pack may not be correctly attached; try reattaching it properly. Lastly, if you are using the CP-20, its fuse might be blown. If so, repair the underlying problem and then replace the fuse.
Why Icom IC-A25Ce will not transmit?
If you cannot transmit with your Icom Transceiver, ensure that you have selected a COM band frequency, as you cannot transmit on a weather channel or VOR frequency. Also, check if the battery is exhausted and recharge it if necessary.
What to do if Icom IC-A25Ce keypad is locked?
If your Icom Transceiver displays “Locked” when you push keypad keys or rotate [DIAL], the keypad and [DIAL] are likely locked. To unlock them, push [F], and then push [ ].
Why scan does not start on Icom IC-A25Ce?
If the scan function does not start on your Icom Transceiver, it may be because all memory channels in the selected group are not tagged. To resolve this, tag memory channels on the Menu screen.
How to turn on beep sound on Icom IC-A25Ce?
If you are not hearing any beep sounds on your Icom Transceiver, the beep output level may be set to OFF. Adjust the beep output level on the Menu screen by going to [MENU] > Sounds Settings > Beep.
General| Channel Capacity | 200 channels |
|---|---|
| Channel Spacing | 8.33 kHz / 25 kHz |
| Power Supply Requirement | 7.2V DC |
| Type | Handheld VHF Air Band Transceiver |
| Frequency Range | 118.000 - 136.991 MHz |
| Operating Temperature Range | -10°C to +60°C |
| Modulation | AM |
| Audio Output Power | 700mW (at 16Ω load) |
| Mode | AM |
| Display | LCD |
Details frequency setting, receiving, squelch adjustment, ANL function, and transmitting procedures.
Illustrates the specific keys for VOR and Waypoint navigation functions.
Describes the components of the CDI screen, such as compass rose and deviation needle.
Step-by-step instructions for setting the course heading using the Omni Bearing Selector.
Explains how to set the course heading, confirm TO/FROM indicator, and maintain heading to the VOR station.
Details the components of the Waypoint Navigation screen, including Icon and Navigation areas.
Outlines methods to select a destination waypoint, including from memory or flight plans.
Explains how to select and follow a flight plan, including automatic waypoint advancement.
Details how to manage flight plans, including adding new ones.
Step-by-step guide to create and save a new flight plan with waypoints.
Procedures for modifying the name, waypoints, or other details of a flight plan.
Detailed instructions on starting, stopping, and controlling scan direction.
Provides steps to access and edit memory channel details.
Instructions for editing the name of a memory channel, including usable characters.
Instructions for editing RX/TX frequencies, including duplex settings.
Procedures for removing memory channels.
Guides on saving current position as a waypoint and saving selected frequencies.
Instructions for saving the current GPS position as a waypoint.
Details on saving a selected frequency to a memory channel.
Provides steps to set a priority channel and enable the priority watch function.
Details selecting, receiving alerts, and scanning weather channels.
Explains how to turn on the duplex setting and set the transmit frequency for communication.
Describes the capabilities and range of the built-in Bluetooth unit.
Detailed steps for pairing headsets, including turning on Bluetooth and entering pairing mode.
Steps for searching, selecting, and pairing a Bluetooth headset.
Detailed steps for pairing LE devices, including time limits.
Lists and describes sub-menus within Waypoint Navigation, including OFF, Disp, and Direct-To WPT.
Details Bluetooth settings, including headset options and device information.
Options for editing, deleting, and customizing memory channels.
Various settings for radio functions like Time Out Timer, Weather Alert, Duplex, and VOX.
Details common issues like no power, no sound, inability to transmit, keypad lock, and scan start problems with solutions.
Instructions on how to replace a blown fuse in the optional cigarette lighter cable.
