Icom IC-R8500 Service Manual

5-6
S-METER FLAT
ADJUSTMENT
ADJUSTMENT
ADJUSTMENT
ADJUSTMENT CONDITIONS
DOT MATRIX DISPLAY
OPERATION
ENTERING
ADJUSTMENT
SET MODE
•
Connect a terminator to the [REMOTE]
connector on the rear
panel
•
While pushing
the [M-CH] and [ENT]
switches, turn
power
ON.
Pu.Sp’l
0 1 jci
*2*
Push
[3]
to enter S-meter
flat
set
mode. Once entering
mode, use [M-CH]
/
[ENT]
switches to select item.
S-METER
FLAT-
48
«
Connect an SSG to
the
antenna
con-
nector for
0.1-30
MHz (SOQANT)
and
set as;
Frequency
: Same
freq. as displayed
Level :50uV"(-73dBm)
Modulation: OFF
•
Receiving
SIG_F
0.
.3M
•
Pushing
and
holding
the
[M-CH],
49
•
Set an SSG frequency
as disf^ayed.
siG_F
i.en
•
Pushing and holding
the
[M-CH].
50
•
Set an
SSG
frequency
as
displayed.
SIG_F
i.sn
•
Pushing and holding the
[M-CH].
51
•
Set an SSG frequency
as displayed.
»
Pushing and holding the
[M-CH].
52 Set
an
SSG
frequency
as displayed.
SIG._F
6. 0M
•
Pushing and holding
the
[M-CH].
53
•
Set an
SSG
frequency
as displayed.
SIG_F
9. 5f1
•
Pushing and holding
the
[M-CH].
54 Set
an
SSG frequency
as displayed.
SIG„F
13. 0M
•
Pushing and holding
the
^
[M-CH].
55
•
Set an SSG frequency as displayed.
:3IG_F
IS. 5M
•
Pushing
and holding the
[M-CH].
56
•
Set an SSG
frequency
as
displayed.
SIG„F
26.
0M
•
Pushing and holding
the
[M-CH].
57
•
Connect an
SSG to the antenna con-
nector for
30-2000
MHz and set
as:
Frequency
: Same freq. as displayed
Level
:50uV*(-73dBm)
Modulation; OFF
*
Receiving
SIG_F
1127.
0M
•
Pushing
and holding
the
[M-CH].
58
•
Set an SSG frequency as displayed.
SIG_F
1204.
011
«
Pushing and holding the
[M-CH].
59
•
Set an SSG
frequency as displayed.
SIG_F
1371.01-1
•
Pushing
and holding the
(M-CH).
60
•
Set an
SSG
frequency
as
displayed. •
Pushing
and holding
the
[M-CH].
61 •
Set an SSG
frequency
as displayed.
SIG-F
1094. in
•
Pushing
and holding the
[M-CH].
62 «
Set an SSG frequency as displayed.
SIG_.F
1990. 0M
•
Pushing
and holding
the
[M-CHj.
63
•
Set
an
SSG frequency
as displayed.
SIG_F
1999.
9ri
•
Pushing and holding
the
(M-CHJ.
This outpul tevel
ol a standard signal
generator
(SSG) is indicated
SSQ's
open circuK.
5-10

Icom IC-R8500 Specifications

General

Antenna Impedance	50 Ω
Power Supply	13.8 V DC ±15%
Mode	AM, FM, WFM, CW
Channels	1000
Tuning Steps	10 kHz
Dynamic Range	100 dB
IF Output	10.7 MHz
Antenna Input	SO-239