Why is the sensitivity low on my Icom IC-R6 Receiver?
If your Icom Receiver's sensitivity is low, and you can only hear strong signals, it's possible that the attenuator function is activated. To turn it off, hold down the [FUNC] button and push the [SQL] button.
How to fix an Icom IC-R6 Receiver that won't turn on?
If your Icom Receiver isn't powering on, the batteries may be exhausted. Try replacing or charging them. Also, check the battery polarity to ensure it's correct.
How to unlock frequency settings on Icom Receiver?
If the frequency cannot be set on your Icom Receiver, the lock function may be activated. To turn it off, hold down the [FUNC] button and push the [ ](BAND) button for 1 second.
Why is the audio distorted on my Icom Receiver?
If the audio from your Icom Receiver is distorted, the operating mode may not be selected correctly. Push the [MODE] button repeatedly to select a suitable operating mode.
Why doesn't programmed scan start on my Icom IC-R6?
If the programmed scan on your Icom Receiver does not start, it may be because program scan edges are not programmed. Program a pair of scan edge channels.
Why memory or bank scan does not start on Icom IC-R6 Receiver?
If the memory or bank scan on your Icom Receiver does not start, it could be because no or only one memory or bank channel is programmed. Program at least 2 memory or bank channels.
What to do if no sound comes from the Icom IC-R6 Receiver speaker?
If no sound is coming from the Icom Receiver's speaker, first, try pushing the [Y] button to adjust the volume to a suitable level. If the volume isn't the issue, check the squelch level by holding down [SQL] and rotating [DIAL] to adjust it. Finally, ensure that a different tone squelch tone is not selected; if it is, turn the appropriate function OFF.
What to do if installed batteries cannot be charged in Icom Receiver?
If the installed batteries in your Icom Receiver cannot be charged, it's possible they are over discharged. Try re-installing the batteries (wait at least 2 seconds), then plug in the AC adapter or CP-18A/E while holding down the [FUNC] button.
How to turn on beep sounds on Icom Receiver?
If there are no beep sounds on your Icom Receiver, the beep tones may be turned OFF, or the beep tone level is too low. Turn the beep tone ON, or set the beep tone level to an appropriate level in the Set mode.
What to do if desired Set mode item cannot be selected on Icom IC-R6 Receiver?
If you cannot select your desired Set mode item on the Icom Receiver, the “EXPAND” item is likely set to OFF. Turn the “EXPAND” item ON.
Details on the function of specific keys like FUNC, SQL, DIAL, and UP/DOWN keys.
Instructions for correctly installing batteries into the receiver.
Procedures for charging the rechargeable batteries for the receiver.
How to select, program, and manage memory channels.
Steps for receiving signals, adjusting volume, and squelch levels.
How to select, program, name, and clear memory channels.
Setting up and selecting memory banks for organized storage.
Overview and starting procedures for various scan types.
Performing scans on memory channels and banks.
Performing partial and all resets for troubleshooting.
Solutions for problems like no power, no sound, or setting errors.
General| Product color | Black |
|---|---|
| Channels quantity | 1550 channels |
| Supported radio bands | AM, FM |
| Battery type | AA |
| Number of batteries supported | 2 |
| Impedance | 16 Ω |
| Frequency range | 0.1 - 1309.995 MHz |
| Product type | Portable CB radio |
| Housing material | - |
Weight and Dimensions| Depth | 29.8 mm |
|---|---|
| Width | 58 mm |
| Height | 86 mm |
| Weight | 200 g |
To Next Page
