x« FC4A MICROSMART USER’S MANUAL »
INDEX
M8117 25-6
number 25-7, 25-8
SOTU and SOTD instructions 7-22
SOTU/SOTD instructions using with program
branching
18-2
source
and destination operands
8-5
operand 8-5
special
functions
1-2, 5-1
input tab 5-11, 5-12, 5-18, 5-20, 5-22
special data registers 6-14
for analog potentiometers 5-30, 6-15
for analog voltage input 5-31
for calendar/clock data 15-5
for data link communication error 25-4
for data link master/slave stations 6-15
for error information 29-3
for high-speed counter 5-7, 5-8, 5-9, 5-10, 6-15
for HMI module 6-15
for interrupt inputs 5-20
for modem mode 27-3
for port 2 6-16
for pulse outputs 6-15, 20-4, 20-17
for RS232C line control signals 17-29
for scan time 5-27
for timer interrupt 5-22
special internal relays 6-7
for calendar/clock data 15-6
for catch inputs 5-18
for data link communication 25-6
for expansion data registers 5-44
for high-speed counter 5-6, 5-7, 5-9, 5-10
for interrupt inputs 5-20
for interrupt status 18-7
for modem mode 27-2
for timer interrupt 5-22
read only 6-8
read/write 6-7
specifications
AC input module
2-25
analog
I/O module
2-45
input 2-46, 2-47, 2-49
output 2-50
AS-Interface module 2-58
catch input 5-18
clock cartridge 2-67
communication
adapter
2-62
module 2-62
CPU module 2-4, 2-14
data link 25-1
DC input
CPU module
2-6, 2-16
input module 2-24
mixed I/O module 2-40
function 2-4, 2-14
general 2-3, 2-13, 2-45
HMI module 2-59
memory cartridge 2-64
mixed I/O module 2-40
relay output
CPU module
2-7, 2-18
mixed I/O module 2-41
output module 2-31
RS232C/RS485 converter 26-4
serial interface 26-4
single-phase high-speed counter 5-8, 5-10
transistor
output CPU module
2-17
sink output module 2-33
source output module 2-36
two-phase high-speed counter 5-7, 5-9
user communication mode 17-2
standard slaves 28-4
start
and result internal relays
27-2
control M8000 6-10
delimiter 17-18
WindLDR 4-5
start/stop
operation
4-3
schematic 4-3
using HMI module 5-39
using power supply 4-4
using WindLDR 4-3
status
code
intelligent module access
23-6
receive 17-23
transmit 17-11
data register modem mode 27-7
information 28-23
internal relays 28-23
internal relays 27-2
LED M8010 6-10
LEDs 28-16, 28-17
relay 20-3, 20-9, 20-17, 20-26
system 2-4, 2-14, 4-4
step response method 21-10
steps 30-3
stop
input
4-4, 5-2
system status 2-4, 2-14
stop access
read
23-4
write 23-5
STOP mode control signal status 17-29
STPA READ 23-4
STPA WRITE 23-5
strip direct mounting 3-7
structure of an advanced instruction 8-5
SUB 11-1
subroutine 18-4
subtraction 11-1
SwitchNet 1-8
data I/O port 28-35
slaves internal relays 28-37
system
program version D8029
6-17, 29-1
requirements 28-2
setup 1-4, 28-6
data link 25-2