IKEA RENGORA Instruction Manual

Zum Herunterladen der vollständigen Version besuchen Sie bitte www.ikea.com
12DEUTSCH
Klarspülerspender auüllen
Klarspüler macht das TROCKNEN von Geschirr einfacher.
Der Klarspülerspender A muss aufgefüllt werden, wenn das
KLARSPÜLER AUFFÜLLEN Anzeigelicht
1. Upper rack
2. ฀฀฀฀฀฀฀
3. Upper rack height adjuster
4. Upper sprayer arm
5. Lower rack
6. Cutlery basket
7. Lower sprayer arm
8. Filter Assembly
9. Salt reservoir
10. Detergent and Rinse Aid dispensers
11. Rating plate
12. Control panel
ADVICE REGARDING THE FIRST TIME USE
After installation, remove the stoppers from the racks and the
retaining elastic elements from the upper rack.
FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on the
dishes andon the machine’s functional components.
• It is important that the salt reservoir be never empty.
• It is important to set the water hardness.
The salt reservoir is located in the lower part of the
dishwasher (see PRODUCT DESCRIPTION) and should be
filled when the SALT REFILL indicator light in the
control panel is lit .
1. Remove the lower rack and
unscrew the reservoir cap
(anticlockwise).
2. Only the first time you do this: fill
the salt reservoir with water.
3. Position the funnel (see figure)
and fill the salt reservoir right up
to its edge (approximately 1 kg);
it is not unusual for a little water to
leak out.
4. Remove the funnel and wipe any
salt residue away from the
opening.
1. On-Off/Reset button with indicator light
2. Program selection button
3. Salt refill indicator ligh
4. Rinse Aid refill indicator ligh
5. Program number and delay time indicator
6. Tablet indicator light
7. Display
8. Half Load indicator light
9. Half Load button
10. Delay button
11. START/Pause button with indicator light / Tab
1 2 3 4 5 6 7 8 9 10
11
auf der Bedienblende
leuchtet.
A
B
B
A
1. Den Behälter
B
durch Drücken und Anheben der Zunge am
Deckelönen.
2. Den Klarspüler vorsichtig bis zur maximalen
Füllstandsmarkierung(110ml)anderFüllönungeinfüllen
und ein Überlaufen vermeiden. Andernfalls sofort mit einem
trockenen Tuch abwischen.
3. Den Deckel schließen bis er einrastet.
Füllen Sie den Klarspüler NIEMALS direkt ins Innere des
Geschirrspülers.
Klarspülerdosierung
Sollte das Trockenergebnis unzufriedenstellend sein, kann die
Klarspülerdosierung neu eingestellt werden.
• Den Geschirrspüler mit der Taste EIN/AUS einschalten.
• Mit der Taste EIN/AUS ausschalten.
• Drücken Sie die Taste
• Switch on the appliance by pressing the ON/OFF button.
• Switch off the appliance by pressing the ON/OFF button.
• Hold down button
for 5 seconds, until you hear a beep.
• Switch on the appliance by pressing the ON/OFF button.
•
•
The current selection level number and the salt indicator light
฀฀฀฀฀฀
Press button to select the desired hardness level (see
WATER HARDNESS TABLE).
• Switch off the appliance by pressing the ON/OFF button.
Setting is complete!
Water Hardness Table
Level
°dH
German degrees
°fH
French degrees
1 Soft 0 - 6 0 - 10
2 Medium 7 - 11 11 - 20
3 Average 12 - 17 21 - 30
4 Hard 18 - 34 31 - 60
5 Very hard 35 - 50 61 - 90
Make sure the cap is screwed on tightly, so that no detergent can
get into the container during the wash program (this could damage
the water softener beyond repair).
As soon as this procedure is complete, run a program without
loading. The “Pre-Wash” program alone is NOT฀฀฀฀฀฀
Residual saline solution or grains of salt can lead to corrosion,
irreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such
circumstances.
฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀s.
฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀
heating element may be damaged as a result.
Whenever you need to add salt, it is mandatory to complete
the procedure before the beginning of the washing cycle.
SETTING THE WATER HARDNESS
To allow the water softener to work in a perfect way, it is essential
that the water hardness setting is based on the actual water hard-
ness in your house. This information can be obtained from your local
water supplier. The factory setting is for average (3) water hardness.
FILLING THE RINSE AID DISPENSER
A
should be lled when the RINSE AID REFILL indicator light
B
(110 ml) reference notch of the lling space - avoid spilling it.
NEVER pour the rinse aid directly into the tub.
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satised with the drying results, you can
The current selection level number and rinse aid indicator light ash.
the dishwasher model. The factory setting is specic to the model,
FILLING THE DETERGENT DISPENSER
฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀
dishwashers.
useof detergent, rinse aid liquid and rened salt is required.
To open the detergent dispenser
press button A.
Introduce the detergent into
the dry dispenser B only.
Place the amount of detergent
for pre-washing directly inside
the tub.
A
B
B
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the TABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
drei Mal - ein Piepton ertönt.
• Mit der Taste EIN/AUS einschalten.
• Die Nummer der aktuell ausgewählten Stufe und die
Klarspülernachfüllanzeige blinken.
• Drücken Sie die Taste
• Switch on the appliance by pressing the ON/OFF button.
• Switch off the appliance by pressing the ON/OFF button.
• Hold down button
for 5 seconds, until you hear a beep.
• Switch on the appliance by pressing the ON/OFF button.
•
•
The current selection level number and the salt indicator light
฀฀฀฀฀฀
Press button to select the desired hardness level (see
WATER HARDNESS TABLE).
• Switch off the appliance by pressing the ON/OFF button.
Setting is complete!
Water Hardness Table
Level
°dH
German degrees
°fH
French degrees
1 Soft 0 - 6 0 - 10
2 Medium 7 - 11 11 - 20
3 Average 12 - 17 21 - 30
4 Hard 18 - 34 31 - 60
5 Very hard 35 - 50 61 - 90
Make sure the cap is screwed on tightly, so that no detergent can
get into the container during the wash program (this could damage
the water softener beyond repair).
As soon as this procedure is complete, run a program without
loading. The “Pre-Wash” program alone is NOT฀฀฀฀฀฀
Residual saline solution or grains of salt can lead to corrosion,
irreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such
circumstances.
฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀s.
฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀
heating element may be damaged as a result.
Whenever you need to add salt, it is mandatory to complete
the procedure before the beginning of the washing cycle.
SETTING THE WATER HARDNESS
To allow the water softener to work in a perfect way, it is essential
that the water hardness setting is based on the actual water hard-
ness in your house. This information can be obtained from your local
water supplier. The factory setting is for average (3) water hardness.
FILLING THE RINSE AID DISPENSER
A
should be lled when the RINSE AID REFILL indicator light
B
(110 ml) reference notch of the lling space - avoid spilling it.
NEVER pour the rinse aid directly into the tub.
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satised with the drying results, you can
The current selection level number and rinse aid indicator light ash.
the dishwasher model. The factory setting is specic to the model,
FILLING THE DETERGENT DISPENSER
฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀
dishwashers.
useof detergent, rinse aid liquid and rened salt is required.
To open the detergent dispenser
press button A.
Introduce the detergent into
the dry dispenser B only.
Place the amount of detergent
for pre-washing directly inside
the tub.
A
B
B
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the TABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
, um den Stand der gelieferten
Klarspülermenge auszuwählen.
• Mit der Taste EIN/AUS ausschalten.
Die Einstellung ist abgeschlossen!
DieKlarspülerstufekannaufNULL(ECO)eingestelltwerden.
In diesem Fall wird kein Klarspüler ausgegeben. Die
Kontrollleuchte zur ANZEIGE DES FEHLENDEN KLARSPÜLERS
leuchtet nicht mehr auf. Je nach Gerätemodell können bis max.
5 Stufen eingestellt werden. Die Werkseinstellung ist abhängig
vom Modell. Bitte befolgen Sie die Anweisungen oben, um dies
für Ihr Gerät zu überprüfen.
• Wenn Sie bläuliche Streifen auf dem Geschirr sehen, stellen
SieeineniedrigereZahlein(1-2).
• Wenn Wassertropfen oder Kalkablagerungen auf dem
Geschirrsind,einehöhereZahleinstellen(3-4).
Einfüllen des Spülmittels
Die Verwendung von Spülmittel, das nicht für Geschirrspüler
entwickelt wurde, ist, kann zu Funktionsstörungen oder
Schäden am Gerät führen.
Drücken Sie zum Önen des Spülmittelfachs Taste C.
Füllen Sie das Spülmittel ausschließlich in das trockene Fach
D ein.
Geben Sie die Spülmittelmenge für die Vorwäsche direkt in
das Innere des Geschirrspülers.
• Switch on the appliance by pressing the ON/OFF button.
• Switch off the appliance by pressing the ON/OFF button.
• Hold down button
for 5 seconds, until you hear a beep.
• Switch on the appliance by pressing the ON/OFF button.
•
•
The current selection level number and the salt indicator light
฀฀฀฀฀฀
Press button to select the desired hardness level (see
WATER HARDNESS TABLE).
• Switch off the appliance by pressing the ON/OFF button.
Setting is complete!
Water Hardness Table
Level
°dH
German degrees
°fH
French degrees
1 Soft 0 - 6 0 - 10
2 Medium 7 - 11 11 - 20
3 Average 12 - 17 21 - 30
4 Hard 18 - 34 31 - 60
5 Very hard 35 - 50 61 - 90
Make sure the cap is screwed on tightly, so that no detergent can
get into the container during the wash program (this could damage
the water softener beyond repair).
As soon as this procedure is complete, run a program without
loading. The “Pre-Wash” program alone is NOT฀฀฀฀฀฀
Residual saline solution or grains of salt can lead to corrosion,
irreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such
circumstances.
฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀s.
฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀
heating element may be damaged as a result.
Whenever you need to add salt, it is mandatory to complete
the procedure before the beginning of the washing cycle.
SETTING THE WATER HARDNESS
To allow the water softener to work in a perfect way, it is essential
that the water hardness setting is based on the actual water hard-
ness in your house. This information can be obtained from your local
water supplier. The factory setting is for average (3) water hardness.
FILLING THE RINSE AID DISPENSER
A
should be lled when the RINSE AID REFILL indicator light
B
(110 ml) reference notch of the lling space - avoid spilling it.
NEVER pour the rinse aid directly into the tub.
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satised with the drying results, you can
The current selection level number and rinse aid indicator light ash.
the dishwasher model. The factory setting is specic to the model,
FILLING THE DETERGENT DISPENSER
฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀
dishwashers.
useof detergent, rinse aid liquid and rened salt is required.
To open the detergent dispenser
press button A.
Introduce the detergent into
the dry dispenser B only.
Place the amount of detergent
for pre-washing directly inside
the tub.
A
B
B
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the TABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
D
C
1. Hinsichtlich der Dosierung verweisen wir auf die zuvor
erwähnte Information, in der die richtige Menge angegeben
ist. Im Fach
D
sind Anzeigen, die bei der Spülmitteldosierung
helfen.
2. Entfernen Sie eventuelle Spülmittelrückstände von den
Kanten der Kammern und schließen Sie den Deckel so, dass
er einrastet.
3. Schieben Sie den Deckel der Spülmittelkammer zum Schließen
nach oben, bis er einrastet.
DieSpülmittelkammerönetsichautomatischzumrichtigen
Zeitpunkt des jeweils gewählten Programms. Werden
Kombispülmittel verwendet, dann empfehlen wir, die Option
TAB zu verwenden. Damit werden die Programme dem
verwendeten Spülmittel angepasst, um das bestmögliche
Spülergebnis zu erhalten.
Bedienfeld
1
Ein-Aus/Reset Taste mit Anzeigelicht
2
Programmwahl-Taste
3
AnzeigelichtzumSalzauüllen
4
AnzeigelichtzumKlarspülerauüllen
5
Programmnummer und Verzögerungszeit-Anzeige
6
Tab-Anzeigelicht
7
Display
8
Anzeigelicht halbe Füllmenge
9
Halbe-Füllmenge-Taste
10
Startvorwahl-Taste
11
START/Pause-Taste mit Anzeigelicht/Tab
3sec
h
1 2 3 4 5 6 8 9 10 11
7
7 PROGRAMS
1 2 3 4
5
6
55° 65°50°
50° 65°
7
65°

IKEA RENGORA Specifications

General

Capacity	13 Place Settings
Number of Programs	5
Delay Start	Yes
Child Lock	Yes
Type	Built-in