IKEA RENGORA - Panneau de Commande

Pour télécharger la version complète, rendez-vous sur le site www.ikea.com
22FRANÇAIS
Remplir le distributeur de liquide de rinçage
Le liquide de rinçage permet à la vaisselle de SÉCHER plus
facilement. Le distributeur de liquide de rinçage A devrait être
rempli lorsque le voyant de NIVEAU DE LIQUIDE DE RINÇAGE
1. Upper rack
2. ฀฀฀฀฀฀฀
3. Upper rack height adjuster
4. Upper sprayer arm
5. Lower rack
6. Cutlery basket
7. Lower sprayer arm
8. Filter Assembly
9. Salt reservoir
10. Detergent and Rinse Aid dispensers
11. Rating plate
12. Control panel
ADVICE REGARDING THE FIRST TIME USE
After installation, remove the stoppers from the racks and the
retaining elastic elements from the upper rack.
FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on the
dishes andon the machine’s functional components.
• It is important that the salt reservoir be never empty.
• It is important to set the water hardness.
The salt reservoir is located in the lower part of the
dishwasher (see PRODUCT DESCRIPTION) and should be
filled when the SALT REFILL indicator light in the
control panel is lit .
1. Remove the lower rack and
unscrew the reservoir cap
(anticlockwise).
2. Only the first time you do this: fill
the salt reservoir with water.
3. Position the funnel (see figure)
and fill the salt reservoir right up
to its edge (approximately 1 kg);
it is not unusual for a little water to
leak out.
4. Remove the funnel and wipe any
salt residue away from the
opening.
1. On-Off/Reset button with indicator light
2. Program selection button
3. Salt refill indicator ligh
4. Rinse Aid refill indicator ligh
5. Program number and delay time indicator
6. Tablet indicator light
7. Display
8. Half Load indicator light
9. Half Load button
10. Delay button
11. START/Pause button with indicator light / Tab
1 2 3 4 5 6 7 8 9 10
11
est allumé sur le panneau de commande.
A
B
B
A
1. Ouvrez le distributeur
B
en appuyant et en tirant sur la
languette sur le couvercle.
2. Versez doucement du liquide de rinçage jusqu'à la marque
de référence (110 ml) du réservoir de remplissage - évitez
les débordements. Si cela se produit, nettoyez les dégâts
immédiatement avec un linge sec.
3. Appuyez sur le bouchon pour le fermer; un clic se fait
entendre.
Ne JAMAIS verser le liquide de rinçage directement dans la
cuve.
Ajuster le dosage du liquide de rinçage
Si vous n'êtes pas complètement satisfait avec le séchage, vous
pouvez ajuster la quantité de liquide de rinçage utilisée.
• Allumez le lave-vaisselle en utilisant la touche MARCHE/ARRÊT.
• Éteignez-le en utilisant la touche MARCHE/ARRÊT.
• Appuyez sur la touche
• Switch on the appliance by pressing the ON/OFF button.
• Switch off the appliance by pressing the ON/OFF button.
• Hold down button
for 5 seconds, until you hear a beep.
• Switch on the appliance by pressing the ON/OFF button.
•
•
The current selection level number and the salt indicator light
฀฀฀฀฀฀
Press button to select the desired hardness level (see
WATER HARDNESS TABLE).
• Switch off the appliance by pressing the ON/OFF button.
Setting is complete!
Water Hardness Table
Level
°dH
German degrees
°fH
French degrees
1 Soft 0 - 6 0 - 10
2 Medium 7 - 11 11 - 20
3 Average 12 - 17 21 - 30
4 Hard 18 - 34 31 - 60
5 Very hard 35 - 50 61 - 90
Make sure the cap is screwed on tightly, so that no detergent can
get into the container during the wash program (this could damage
the water softener beyond repair).
As soon as this procedure is complete, run a program without
loading. The “Pre-Wash” program alone is NOT฀฀฀฀฀฀
Residual saline solution or grains of salt can lead to corrosion,
irreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such
circumstances.
฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀s.
฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀
heating element may be damaged as a result.
Whenever you need to add salt, it is mandatory to complete
the procedure before the beginning of the washing cycle.
SETTING THE WATER HARDNESS
To allow the water softener to work in a perfect way, it is essential
that the water hardness setting is based on the actual water hard-
ness in your house. This information can be obtained from your local
water supplier. The factory setting is for average (3) water hardness.
FILLING THE RINSE AID DISPENSER
A
should be lled when the RINSE AID REFILL indicator light
B
(110 ml) reference notch of the lling space - avoid spilling it.
NEVER pour the rinse aid directly into the tub.
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satised with the drying results, you can
The current selection level number and rinse aid indicator light ash.
the dishwasher model. The factory setting is specic to the model,
FILLING THE DETERGENT DISPENSER
฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀
dishwashers.
useof detergent, rinse aid liquid and rened salt is required.
To open the detergent dispenser
press button A.
Introduce the detergent into
the dry dispenser B only.
Place the amount of detergent
for pre-washing directly inside
the tub.
A
B
B
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the TABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
à trois reprises - vous entendrez un
signal sonore.
• Allumez-le en utilisant la touche MARCHE/ARRÊT.
• Le numéro du niveau de sélection actuelle et le voyant du
niveau de liquide de rinçage clignotent.
• Appuyez sur la touche
• Switch on the appliance by pressing the ON/OFF button.
• Switch off the appliance by pressing the ON/OFF button.
• Hold down button
for 5 seconds, until you hear a beep.
• Switch on the appliance by pressing the ON/OFF button.
•
•
The current selection level number and the salt indicator light
฀฀฀฀฀฀
Press button to select the desired hardness level (see
WATER HARDNESS TABLE).
• Switch off the appliance by pressing the ON/OFF button.
Setting is complete!
Water Hardness Table
Level
°dH
German degrees
°fH
French degrees
1 Soft 0 - 6 0 - 10
2 Medium 7 - 11 11 - 20
3 Average 12 - 17 21 - 30
4 Hard 18 - 34 31 - 60
5 Very hard 35 - 50 61 - 90
Make sure the cap is screwed on tightly, so that no detergent can
get into the container during the wash program (this could damage
the water softener beyond repair).
As soon as this procedure is complete, run a program without
loading. The “Pre-Wash” program alone is NOT฀฀฀฀฀฀
Residual saline solution or grains of salt can lead to corrosion,
irreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such
circumstances.
฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀s.
฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀
heating element may be damaged as a result.
Whenever you need to add salt, it is mandatory to complete
the procedure before the beginning of the washing cycle.
SETTING THE WATER HARDNESS
To allow the water softener to work in a perfect way, it is essential
that the water hardness setting is based on the actual water hard-
ness in your house. This information can be obtained from your local
water supplier. The factory setting is for average (3) water hardness.
FILLING THE RINSE AID DISPENSER
A
should be lled when the RINSE AID REFILL indicator light
B
(110 ml) reference notch of the lling space - avoid spilling it.
NEVER pour the rinse aid directly into the tub.
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satised with the drying results, you can
The current selection level number and rinse aid indicator light ash.
the dishwasher model. The factory setting is specic to the model,
FILLING THE DETERGENT DISPENSER
฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀
dishwashers.
useof detergent, rinse aid liquid and rened salt is required.
To open the detergent dispenser
press button A.
Introduce the detergent into
the dry dispenser B only.
Place the amount of detergent
for pre-washing directly inside
the tub.
A
B
B
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the TABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
pour sélectionner la quantité de
liquide de rinçage qui doit être utilisée.
• Éteignez-le en utilisant la touche MARCHE/ARRÊT.
Le réglage est terminé!
Si le niveau de liquide de rinçage est à ZÉRO (ÉCO), il n'y aura
pas de liquide de rinçage distribué. Le voyant LIQUIDE DE
RINÇAGE BAS ne s'allumera pas s'il ne reste plus de liquide de
rinçage. Un maximum de 5 niveaux peuvent être réglés selon le
modèledulave-vaisselle.Lesréglagesd'usinesontspéciques
au modèle, merci de suivre les instructions ci-dessus pour
vérierceuxquis'appliquentàvotremachine.
• • Si vous observez des traces bleuâtres sur la vaisselle, placez
sur un niveau plus bas (1-2).
• • Si vous observez des gouttelettes d'eau ou des traces de
calcaire sur la vaisselle, placez sur un niveau plus haut (3-4).
Remplir de distributeur de détergent
L'utilisation de détergent non conçu pour les lave-vaisselles
peut provoque un dysfonctionnement ou un dommage à
l'appareil.
Pour ouvrir le distributeur de détergent, appuyez sur le
bouton C.
Insérez le détergent dans le distributeur sec D uniquement.
Placez la quantité de détergent pour le prélavage
directement dans la cuve.
• Switch on the appliance by pressing the ON/OFF button.
• Switch off the appliance by pressing the ON/OFF button.
• Hold down button
for 5 seconds, until you hear a beep.
• Switch on the appliance by pressing the ON/OFF button.
•
•
The current selection level number and the salt indicator light
฀฀฀฀฀฀
Press button to select the desired hardness level (see
WATER HARDNESS TABLE).
• Switch off the appliance by pressing the ON/OFF button.
Setting is complete!
Water Hardness Table
Level
°dH
German degrees
°fH
French degrees
1 Soft 0 - 6 0 - 10
2 Medium 7 - 11 11 - 20
3 Average 12 - 17 21 - 30
4 Hard 18 - 34 31 - 60
5 Very hard 35 - 50 61 - 90
Make sure the cap is screwed on tightly, so that no detergent can
get into the container during the wash program (this could damage
the water softener beyond repair).
As soon as this procedure is complete, run a program without
loading. The “Pre-Wash” program alone is NOT฀฀฀฀฀฀
Residual saline solution or grains of salt can lead to corrosion,
irreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such
circumstances.
฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀s.
฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀
heating element may be damaged as a result.
Whenever you need to add salt, it is mandatory to complete
the procedure before the beginning of the washing cycle.
SETTING THE WATER HARDNESS
To allow the water softener to work in a perfect way, it is essential
that the water hardness setting is based on the actual water hard-
ness in your house. This information can be obtained from your local
water supplier. The factory setting is for average (3) water hardness.
FILLING THE RINSE AID DISPENSER
A
should be lled when the RINSE AID REFILL indicator light
B
(110 ml) reference notch of the lling space - avoid spilling it.
NEVER pour the rinse aid directly into the tub.
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satised with the drying results, you can
The current selection level number and rinse aid indicator light ash.
the dishwasher model. The factory setting is specic to the model,
FILLING THE DETERGENT DISPENSER
฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀
dishwashers.
useof detergent, rinse aid liquid and rened salt is required.
To open the detergent dispenser
press button A.
Introduce the detergent into
the dry dispenser B only.
Place the amount of detergent
for pre-washing directly inside
the tub.
A
B
B
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the TABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
D
C
1. Lorsque vous mesurez le détergent, reportez-vous à
l'information mentionnée plus haut pour ajouter la bonne
quantité. À l'intérieur du distributeur
D
se trouvent des
indications pour aider au dosage de détergent.
2. Enlevez les résidus de détergent sur le bord des récipients
avant de fermer le couvercle; un clic se fait entendre.
3. Fermez le couvercle du distributeur de détergent en le tirant
vers le haut jusqu'à ce que le dispositif soit fermement en
place.
Le distributeur de détergent s'ouvre automatiquement, au
moment déterminé par le programme. Si vous utilisez un
détergent « tout-en-un », nous vous conseillons d'utiliser la
touche PASTILLE, elle ajuste le programme de façon à toujours
obtenir les meilleurs résultats de lavage et séchage.
Panneau de commande
1
Touche et voyant Marche-Arrêt/Réinitialisation
2
Bouton de sélection de programme
3
Témoin de remplissage de sel
4
Témoin de remplissage de liquide de rinçage
5
Voyant pour le numéro du programme et le temps
restant
6
Voyant tablette
7
Écran
8
Témoin Demi-charge
9
Bouton Demi-charge
10
Boutondedémarragediéré
11
Bouton DÉPART/Pause avec témoin / Tablette
3sec
h
1 2 3 4 5 6 8 9 10 11
7
7 PROGRAMS
1 2 3 4
5
6
55° 65°50°
50° 65°
7
65°