IKEA RENGORA - Page 23

Pour télécharger la version complète, rendez-vous sur le site www.ikea.com
23FRANÇAIS
Fonctions
NATURALDRY
Le Système d'ouverture de porte NaturalDry est un système
de séchage à convection qui ouvre automatiquement la porte
pendant/après la phase de séchage pour assurer une performance
de séchage exceptionnelle chaque jour. La porte s'ouvre à une
température qui est sûre pour les meubles de votre cuisine.
Ne sortez pas la vaisselle immédiatement après l'ouverture de la
porte mais attendez pour permettre un séchage correct.
La fonction ne peut pas être activée pour tous les programmes,
consulter le tableau des programmes.
À titre de protection supplémentaire contre la vapeur, une feuille de
protectionspéciquementconçueestajoutéeaveclelave-vaisselle.
Pour voir comment monter la feuille de protection, consulter le
(GUIDE D'INSTALLATION).
La fonctionnalité NaturalDry pourrait être désactivée par l'utilisateur
comme suit :
1. Allez au menu de logiciel du lave-vaisselle en appuyant et en
maintenant le bouton
• Switch on the appliance by pressing the ON/OFF button.
• Switch off the appliance by pressing the ON/OFF button.
• Hold down button
for 5 seconds, until you hear a beep.
• Switch on the appliance by pressing the ON/OFF button.
•
•
The current selection level number and the salt indicator light
฀฀฀฀฀฀
Press button to select the desired hardness level (see
WATER HARDNESS TABLE).
• Switch off the appliance by pressing the ON/OFF button.
Setting is complete!
Water Hardness Table
Level
°dH
German degrees
°fH
French degrees
1 Soft 0 - 6 0 - 10
2 Medium 7 - 11 11 - 20
3 Average 12 - 17 21 - 30
4 Hard 18 - 34 31 - 60
5 Very hard 35 - 50 61 - 90
Make sure the cap is screwed on tightly, so that no detergent can
get into the container during the wash program (this could damage
the water softener beyond repair).
As soon as this procedure is complete, run a program without
loading. The “Pre-Wash” program alone is NOT฀฀฀฀฀฀
Residual saline solution or grains of salt can lead to corrosion,
irreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such
circumstances.
฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀s.
฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀
heating element may be damaged as a result.
Whenever you need to add salt, it is mandatory to complete
the procedure before the beginning of the washing cycle.
SETTING THE WATER HARDNESS
To allow the water softener to work in a perfect way, it is essential
that the water hardness setting is based on the actual water hard-
ness in your house. This information can be obtained from your local
water supplier. The factory setting is for average (3) water hardness.
FILLING THE RINSE AID DISPENSER
A
should be lled when the RINSE AID REFILL indicator light
B
(110 ml) reference notch of the lling space - avoid spilling it.
NEVER pour the rinse aid directly into the tub.
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satised with the drying results, you can
The current selection level number and rinse aid indicator light ash.
the dishwasher model. The factory setting is specic to the model,
FILLING THE DETERGENT DISPENSER
฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀
dishwashers.
useof detergent, rinse aid liquid and rened salt is required.
To open the detergent dispenser
press button A.
Introduce the detergent into
the dry dispenser B only.
Place the amount of detergent
for pre-washing directly inside
the tub.
A
B
B
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the TABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
(6 sec).
2. Vous passez au Menu de contrôle NaturalDry, vous pouvez
changer d'état de la fonctionnalité NaturalDry en appuyant sur le
bouton
• Switch on the appliance by pressing the ON/OFF button.
• Switch off the appliance by pressing the ON/OFF button.
• Hold down button
for 5 seconds, until you hear a beep.
• Switch on the appliance by pressing the ON/OFF button.
•
•
The current selection level number and the salt indicator light
฀฀฀฀฀฀
Press button to select the desired hardness level (see
WATER HARDNESS TABLE).
• Switch off the appliance by pressing the ON/OFF button.
Setting is complete!
Water Hardness Table
Level
°dH
German degrees
°fH
French degrees
1 Soft 0 - 6 0 - 10
2 Medium 7 - 11 11 - 20
3 Average 12 - 17 21 - 30
4 Hard 18 - 34 31 - 60
5 Very hard 35 - 50 61 - 90
Make sure the cap is screwed on tightly, so that no detergent can
get into the container during the wash program (this could damage
the water softener beyond repair).
As soon as this procedure is complete, run a program without
loading. The “Pre-Wash” program alone is NOT฀฀฀฀฀฀
Residual saline solution or grains of salt can lead to corrosion,
irreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such
circumstances.
฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀s.
฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀
heating element may be damaged as a result.
Whenever you need to add salt, it is mandatory to complete
the procedure before the beginning of the washing cycle.
SETTING THE WATER HARDNESS
To allow the water softener to work in a perfect way, it is essential
that the water hardness setting is based on the actual water hard-
ness in your house. This information can be obtained from your local
water supplier. The factory setting is for average (3) water hardness.
FILLING THE RINSE AID DISPENSER
A
should be lled when the RINSE AID REFILL indicator light
B
(110 ml) reference notch of the lling space - avoid spilling it.
NEVER pour the rinse aid directly into the tub.
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satised with the drying results, you can
The current selection level number and rinse aid indicator light ash.
the dishwasher model. The factory setting is specic to the model,
FILLING THE DETERGENT DISPENSER
฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀
dishwashers.
useof detergent, rinse aid liquid and rened salt is required.
To open the detergent dispenser
press button A.
Introduce the detergent into
the dry dispenser B only.
Place the amount of detergent
for pre-washing directly inside
the tub.
A
B
B
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the TABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
:
E – activé d – désactivé
Pour conrmer le changement et sortir du Menu Contrôle,
appuyez sur le bouton
• Switch on the appliance by pressing the ON/OFF button.
• Switch off the appliance by pressing the ON/OFF button.
• Hold down button
for 5 seconds, until you hear a beep.
• Switch on the appliance by pressing the ON/OFF button.
•
•
The current selection level number and the salt indicator light
฀฀฀฀฀฀
Press button to select the desired hardness level (see
WATER HARDNESS TABLE).
• Switch off the appliance by pressing the ON/OFF button.
Setting is complete!
Water Hardness Table
Level
°dH
German degrees
°fH
French degrees
1 Soft 0 - 6 0 - 10
2 Medium 7 - 11 11 - 20
3 Average 12 - 17 21 - 30
4 Hard 18 - 34 31 - 60
5 Very hard 35 - 50 61 - 90
Make sure the cap is screwed on tightly, so that no detergent can
get into the container during the wash program (this could damage
the water softener beyond repair).
As soon as this procedure is complete, run a program without
loading. The “Pre-Wash” program alone is NOT฀฀฀฀฀฀
Residual saline solution or grains of salt can lead to corrosion,
irreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such
circumstances.
฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀s.
฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀
heating element may be damaged as a result.
Whenever you need to add salt, it is mandatory to complete
the procedure before the beginning of the washing cycle.
SETTING THE WATER HARDNESS
To allow the water softener to work in a perfect way, it is essential
that the water hardness setting is based on the actual water hard-
ness in your house. This information can be obtained from your local
water supplier. The factory setting is for average (3) water hardness.
FILLING THE RINSE AID DISPENSER
A
should be lled when the RINSE AID REFILL indicator light
B
(110 ml) reference notch of the lling space - avoid spilling it.
NEVER pour the rinse aid directly into the tub.
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satised with the drying results, you can
The current selection level number and rinse aid indicator light ash.
the dishwasher model. The factory setting is specic to the model,
FILLING THE DETERGENT DISPENSER
฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀
dishwashers.
useof detergent, rinse aid liquid and rened salt is required.
To open the detergent dispenser
press button A.
Introduce the detergent into
the dry dispenser B only.
Place the amount of detergent
for pre-washing directly inside
the tub.
A
B
B
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the TABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
et maintenez-le enfoncé (3 sec).
Les données du programme Éco sont mesurées sous des conditions en laboratoire conformément à la norme européenne EN 60436:2019.
Note pour les laboratoires d'essais : Pour obtenir des informations sur les conditions de tests comparatifs EN, merci d'envoyer un courriel à
l'adresse suivante : dw_test_support@whirlpool.com
Aucun prétraitement de la vaisselle n'est nécessaire avant l'un quelconque des programmes.
*) Les options ne peuvent pas toutes être utilisées en même temps.
**)Lesvaleursindiquéespourdesprogrammesdiérentsduprogrammeécosontfourniesàtitreindicatifuniquement.Letempsréelpeut
varier selon des facteurs comme la température et la pression de l'eau, la température de la pièce, la quantité de détergent, la quantité et le
type de vaisselle, l'équilibre de la charge, les options supplémentaires sélectionnées, et la calibration du capteur.
1. ECO - Le programme Éco est adapté pour nettoyer de la vaisselle normalement sale, et pour cette utilisation, il est le programme le plus
ecaceentermesdeconsommationd'énergieetd'eaucombinée,etilestutilisépourévaluerlaconformitéàlalégislationeuropéenneen
matière d'éco-conception.
2. LAVAGE ET SÉCHAGE CONVENTIONNELS - Saleté mixte. Pour la vaisselle normalement sale avec des résidus de nourriture secs.
3. INTENSIF - Programme conseillé pour la vaisselle très sale, surtout les poêles et les casseroles (ne pas utiliser pour la vaisselle délicate).
Programme
Séchage Natural
Dry
Fonctions
disponibles
(*)
Durée du programme
de lavage
(h:min)**)
Consommation
d'eau
(litres/cycle)
Consommation
d'énergie
(kWh/cycle)
1 Éco
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
has been started.
NaturalDry
(INSTALLATION GUIDE)
E d
To conrm the change and exit from the Control Menu please
DELAY
1 12
Duration of
(h:min)
**)
(litres/cycle) (kWh/cycle)
50°
2:45 12.0 0.92
1
Eco
2
Conventional
wash and dry
55° 2:00 15.0 1.35
3
Intensive 65°
- 2:30 15.0 1.50
4
Fast 50°
-
- 0:55 11.5 1.10
5
Sanitizing 65°
- 1:40 11.5 1.30
6
Pre-Wash
-
-
- 0:10 4.5 0.01
7
Self-Clean 65°
-
-
0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
50°
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
has been started.
NaturalDry
(INSTALLATION GUIDE)
E d
To conrm the change and exit from the Control Menu please
DELAY
1 12
Duration of
(h:min)
**)
(litres/cycle) (kWh/cycle)
50°
2:45 12.0 0.92
1
Eco
2
Conventional
wash and dry
55° 2:00 15.0 1.35
3
Intensive 65°
- 2:30 15.0 1.50
4
Fast 50°
-
- 0:55 11.5 1.10
5
Sanitizing 65°
- 1:40 11.5 1.30
6
Pre-Wash
-
-
- 0:10 4.5 0.01
7
Self-Clean 65°
-
-
0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
has been started.
NaturalDry
(INSTALLATION GUIDE)
E d
To conrm the change and exit from the Control Menu please
DELAY
1 12
Duration of
(h:min)
**)
(litres/cycle) (kWh/cycle)
50°
2:45 12.0 0.92
1
Eco
2
Conventional
wash and dry
55° 2:00 15.0 1.35
3
Intensive 65°
- 2:30 15.0 1.50
4
Fast 50°
-
- 0:55 11.5 1.10
5
Sanitizing 65°
- 1:40 11.5 1.30
6
Pre-Wash
-
-
- 0:10 4.5 0.01
7
Self-Clean 65°
-
-
0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
has been started.
NaturalDry
(INSTALLATION GUIDE)
E d
To conrm the change and exit from the Control Menu please
DELAY
1 12
Duration of
(h:min)
**)
(litres/cycle) (kWh/cycle)
50°
2:45 12.0 0.92
1
Eco
2
Conventional
wash and dry
55° 2:00 15.0 1.35
3
Intensive 65°
- 2:30 15.0 1.50
4
Fast 50°
-
- 0:55 11.5 1.10
5
Sanitizing 65°
- 1:40 11.5 1.30
6
Pre-Wash
-
-
- 0:10 4.5 0.01
7
Self-Clean 65°
-
-
0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
2:45 12.0 0.94
2 Lavage et séchage
conventionnels
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
has been started.
NaturalDry
(INSTALLATION GUIDE)
E d
To conrm the change and exit from the Control Menu please
DELAY
1 12
Duration of
(h:min)
**)
(litres/cycle) (kWh/cycle)
50°
2:45 12.0 0.92
1
Eco
2
Conventional
wash and dry
55° 2:00 15.0 1.35
3
Intensive 65°
- 2:30 15.0 1.50
4
Fast 50°
-
- 0:55 11.5 1.10
5
Sanitizing 65°
- 1:40 11.5 1.30
6
Pre-Wash
-
-
- 0:10 4.5 0.01
7
Self-Clean 65°
-
-
0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
55°
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
has been started.
NaturalDry
(INSTALLATION GUIDE)
E d
To conrm the change and exit from the Control Menu please
DELAY
1 12
Duration of
(h:min)
**)
(litres/cycle) (kWh/cycle)
50°
2:45 12.0 0.92
1
Eco
2
Conventional
wash and dry
55° 2:00 15.0 1.35
3
Intensive 65°
- 2:30 15.0 1.50
4
Fast 50°
-
- 0:55 11.5 1.10
5
Sanitizing 65°
- 1:40 11.5 1.30
6
Pre-Wash
-
-
- 0:10 4.5 0.01
7
Self-Clean 65°
-
-
0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
has been started.
NaturalDry
(INSTALLATION GUIDE)
E d
To conrm the change and exit from the Control Menu please
DELAY
1 12
Duration of
(h:min)
**)
(litres/cycle) (kWh/cycle)
50°
2:45 12.0 0.92
1
Eco
2
Conventional
wash and dry
55° 2:00 15.0 1.35
3
Intensive 65°
- 2:30 15.0 1.50
4
Fast 50°
-
- 0:55 11.5 1.10
5
Sanitizing 65°
- 1:40 11.5 1.30
6
Pre-Wash
-
-
- 0:10 4.5 0.01
7
Self-Clean 65°
-
-
0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
has been started.
NaturalDry
(INSTALLATION GUIDE)
E d
To conrm the change and exit from the Control Menu please
DELAY
1 12
Duration of
(h:min)
**)
(litres/cycle) (kWh/cycle)
50°
2:45 12.0 0.92
1
Eco
2
Conventional
wash and dry
55° 2:00 15.0 1.35
3
Intensive 65°
- 2:30 15.0 1.50
4
Fast 50°
-
- 0:55 11.5 1.10
5
Sanitizing 65°
- 1:40 11.5 1.30
6
Pre-Wash
-
-
- 0:10 4.5 0.01
7
Self-Clean 65°
-
-
0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
2:00 15.0 1.35
3 Intensif
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
has been started.
NaturalDry
(INSTALLATION GUIDE)
E d
To conrm the change and exit from the Control Menu please
DELAY
1 12
Duration of
(h:min)
**)
(litres/cycle) (kWh/cycle)
50°
2:45 12.0 0.92
1
Eco
2
Conventional
wash and dry
55° 2:00 15.0 1.35
3
Intensive 65°
- 2:30 15.0 1.50
4
Fast 50°
-
- 0:55 11.5 1.10
5
Sanitizing 65°
- 1:40 11.5 1.30
6
Pre-Wash
-
-
- 0:10 4.5 0.01
7
Self-Clean 65°
-
-
0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
65°
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
has been started.
NaturalDry
(INSTALLATION GUIDE)
E d
To conrm the change and exit from the Control Menu please
DELAY
1 12
Duration of
(h:min)
**)
(litres/cycle) (kWh/cycle)
50°
2:45 12.0 0.92
1
Eco
2
Conventional
wash and dry
55° 2:00 15.0 1.35
3
Intensive 65°
- 2:30 15.0 1.50
4
Fast 50°
-
- 0:55 11.5 1.10
5
Sanitizing 65°
- 1:40 11.5 1.30
6
Pre-Wash
-
-
- 0:10 4.5 0.01
7
Self-Clean 65°
-
-
0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
has been started.
NaturalDry
(INSTALLATION GUIDE)
E d
To conrm the change and exit from the Control Menu please
DELAY
1 12
Duration of
(h:min)
**)
(litres/cycle) (kWh/cycle)
50°
2:45 12.0 0.92
1
Eco
2
Conventional
wash and dry
55° 2:00 15.0 1.35
3
Intensive 65°
- 2:30 15.0 1.50
4
Fast 50°
-
- 0:55 11.5 1.10
5
Sanitizing 65°
- 1:40 11.5 1.30
6
Pre-Wash
-
-
- 0:10 4.5 0.01
7
Self-Clean 65°
-
-
0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
has been started.
NaturalDry
(INSTALLATION GUIDE)
E d
To conrm the change and exit from the Control Menu please
DELAY
1 12
Duration of
(h:min)
**)
(litres/cycle) (kWh/cycle)
50°
2:45 12.0 0.92
1
Eco
2
Conventional
wash and dry
55° 2:00 15.0 1.35
3
Intensive 65°
- 2:30 15.0 1.50
4
Fast 50°
-
- 0:55 11.5 1.10
5
Sanitizing 65°
- 1:40 11.5 1.30
6
Pre-Wash
-
-
- 0:10 4.5 0.01
7
Self-Clean 65°
-
-
0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
2:30 15.0 1.50
4 Lavage rapide
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
has been started.
NaturalDry
(INSTALLATION GUIDE)
E d
To conrm the change and exit from the Control Menu please
DELAY
1 12
Duration of
(h:min)
**)
(litres/cycle) (kWh/cycle)
50°
2:45 12.0 0.92
1
Eco
2
Conventional
wash and dry
55° 2:00 15.0 1.35
3
Intensive 65°
- 2:30 15.0 1.50
4
Fast 50°
-
- 0:55 11.5 1.10
5
Sanitizing 65°
- 1:40 11.5 1.30
6
Pre-Wash
-
-
- 0:10 4.5 0.01
7
Self-Clean 65°
-
-
0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
50° - -
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
has been started.
NaturalDry
(INSTALLATION GUIDE)
E d
To conrm the change and exit from the Control Menu please
DELAY
1 12
Duration of
(h:min)
**)
(litres/cycle) (kWh/cycle)
50°
2:45 12.0 0.92
1
Eco
2
Conventional
wash and dry
55° 2:00 15.0 1.35
3
Intensive 65°
- 2:30 15.0 1.50
4
Fast 50°
-
- 0:55 11.5 1.10
5
Sanitizing 65°
- 1:40 11.5 1.30
6
Pre-Wash
-
-
- 0:10 4.5 0.01
7
Self-Clean 65°
-
-
0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
0:55 11.5 1.10
5 Stérilisation
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
has been started.
NaturalDry
(INSTALLATION GUIDE)
E d
To conrm the change and exit from the Control Menu please
DELAY
1 12
Duration of
(h:min)
**)
(litres/cycle) (kWh/cycle)
50°
2:45 12.0 0.92
1
Eco
2
Conventional
wash and dry
55° 2:00 15.0 1.35
3
Intensive 65°
- 2:30 15.0 1.50
4
Fast 50°
-
- 0:55 11.5 1.10
5
Sanitizing 65°
- 1:40 11.5 1.30
6
Pre-Wash
-
-
- 0:10 4.5 0.01
7
Self-Clean 65°
-
-
0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
65°
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
has been started.
NaturalDry
(INSTALLATION GUIDE)
E d
To conrm the change and exit from the Control Menu please
DELAY
1 12
Duration of
(h:min)
**)
(litres/cycle) (kWh/cycle)
50°
2:45 12.0 0.92
1
Eco
2
Conventional
wash and dry
55° 2:00 15.0 1.35
3
Intensive 65°
- 2:30 15.0 1.50
4
Fast 50°
-
- 0:55 11.5 1.10
5
Sanitizing 65°
- 1:40 11.5 1.30
6
Pre-Wash
-
-
- 0:10 4.5 0.01
7
Self-Clean 65°
-
-
0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
-
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
has been started.
NaturalDry
(INSTALLATION GUIDE)
E d
To conrm the change and exit from the Control Menu please
DELAY
1 12
Duration of
(h:min)
**)
(litres/cycle) (kWh/cycle)
50°
2:45 12.0 0.92
1
Eco
2
Conventional
wash and dry
55° 2:00 15.0 1.35
3
Intensive 65°
- 2:30 15.0 1.50
4
Fast 50°
-
- 0:55 11.5 1.10
5
Sanitizing 65°
- 1:40 11.5 1.30
6
Pre-Wash
-
-
- 0:10 4.5 0.01
7
Self-Clean 65°
-
-
0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
1:40 11.5 1.30
6 Prélavage
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
has been started.
NaturalDry
(INSTALLATION GUIDE)
E d
To conrm the change and exit from the Control Menu please
DELAY
1 12
Duration of
(h:min)
**)
(litres/cycle) (kWh/cycle)
50°
2:45 12.0 0.92
1
Eco
2
Conventional
wash and dry
55°
2:00 15.0 1.35
3
Intensive 65°
- 2:30 15.0 1.50
4
Fast 50°
-
- 0:55 11.5 1.10
5
Sanitizing 65°
- 1:40 11.5 1.30
6
Pre-Wash
-
-
- 0:10 4.5 0.01
7
Self-Clean 65°
-
-
0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
- - -
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
has been started.
NaturalDry
(INSTALLATION GUIDE)
E d
To conrm the change and exit from the Control Menu please
DELAY
1 12
Duration of
(h:min)
**)
(litres/cycle) (kWh/cycle)
50°
2:45 12.0 0.92
1
Eco
2
Conventional
wash and dry
55° 2:00 15.0 1.35
3
Intensive 65°
- 2:30 15.0 1.50
4
Fast 50°
-
- 0:55 11.5 1.10
5
Sanitizing 65°
- 1:40 11.5 1.30
6
Pre-Wash
-
-
- 0:10 4.5 0.01
7
Self-Clean 65°
-
-
0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
0:10 4.5 0.01
7 Auto-nettoyage
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
has been started.
NaturalDry
(INSTALLATION GUIDE)
E d
To conrm the change and exit from the Control Menu please
DELAY
1 12
Duration of
(h:min)
**)
(litres/cycle) (kWh/cycle)
50°
2:45 12.0 0.92
1
Eco
2
Conventional
wash and dry
55° 2:00 15.0 1.35
3
Intensive 65°
- 2:30 15.0 1.50
4
Fast 50°
-
- 0:55 11.5 1.10
5
Sanitizing 65°
- 1:40 11.5 1.30
6
Pre-Wash
-
-
- 0:10 4.5 0.01
7
Self-Clean 65°
-
-
0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
65° - -
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
has been started.
NaturalDry
(INSTALLATION GUIDE)
E d
To conrm the change and exit from the Control Menu please
DELAY
1 12
Duration of
(h:min)
**)
(litres/cycle) (kWh/cycle)
50°
2:45 12.0 0.92
1
Eco
2
Conventional
wash and dry
55° 2:00 15.0 1.35
3
Intensive 65°
- 2:30 15.0 1.50
4
Fast 50°
-
- 0:55 11.5 1.10
5
Sanitizing 65°
- 1:40 11.5 1.30
6
Pre-Wash
-
-
- 0:10 4.5 0.01
7
Self-Clean 65°
-
-
0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
0:50 8.0 0.80
OUVERTURE DE LA
PORTE
ÉCO 50° après 150 min
Lavage et séchage conventionnels
55°
ndecycle
INTENSIF 65° ndecycle
Lavage rapide 50° N/A
STÉRILISATION 65° N/A
PRÉLAVAGE N/A
Auto-nettoyage 65° N/A
Tableau des programmes
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
has been started.
NaturalDry
(INSTALLATION GUIDE)
E d
To conrm the change and exit from the Control Menu please
DELAY
1 12
Duration of
(h:min)
**)
(litres/cycle) (kWh/cycle)
50°
2:45 12.0 0.92
1
Eco
2
Conventional
wash and dry
55° 2:00 15.0 1.35
3
Intensive 65°
- 2:30 15.0 1.50
4
Fast 50°
-
- 0:55 11.5 1.10
5
Sanitizing 65°
- 1:40 11.5 1.30
6
Pre-Wash
-
-
- 0:10 4.5 0.01
7
Self-Clean 65°
-
-
0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
Pourréglerundépartdiéré
1. CHECK WATER CONNECTION
2. SWITCH ON THE DISHWASHER
3.
4.
LOAD THE RACKS (see LOADING THE RACKS)
FILLING THE DETERGENT DISPENSER
(see PROGRAMS TABLE).
5.
6.
7.
CHOOSE THE PROGRAM AND CUSTOMISE THE CYCLE
(see PROGRAMS
DESCRIPTION)
(see OPTIONS AND FUNCTIONS)
START
END OF WASH CYCLE
ashing of the wash cycle number on the display. Open the
The machine will switch off automatically during certain
extended periods of inactivity, in order to minimise electri-
city consumption. If the crockery is only lightly soiled or
if it has been rinsed with water before being placed in the
dishwasher, reduce the amount of detergent used accordingly.
MODIFYING A RUNNING PROGRAM
ON/OFF
ON/OFF
the new wash cycle and any desired options; Start the wash cycle
START/Pause
ADDING EXTRA CROCKERY
START/Pause
be ware of HOT steam!
START/Pause
ACCIDENTAL INTERRUPTIONS
START/Pause
DAILY USE
1. ECO - Normally soiled crockery. Standard program, the most efficient in terms of its combined energy and water
consumption.
2. NORMAL - Mixed soil. For normally soiled dishes with dried food residues.
3. INTENSIVE - Program recommended for heavily soiled crockery, especially suitable for pans and saucepans (not to be used
for delicate items).
4. PRE-WASH - Use to refresh crockery planned to be washed later. No detergent to be used with this program.
5. FAST - Normally soiled crockery. Everyday cycle, that ensures optimal cleaning performance in shorter time.
6. SANITIZING - Normally or heavily soiled crockery, with additional antibacterial wash. Can be used to perform
maintenance of the dishwasher.
7. SELF- CLEAN - Program to be used to perform maintenance of the dishwasher. It cleans the interior of the appliance
using hot water.
(see CONTROL PANEL)
If an option is not compatible with the selected program see PROGRAMS TABLE, the corresponding LED ฀ ฀ ฀ ฀rapidly 3 times
and beeps will sound. The option will not be enabled.
HALF LOAD
Remember to halve the amount of detergent.
The DELAY function cannot be set once a wash cycle
has been started.
TABLET (Tab)
If you use powder or liquid detergent, this option
should be off.
E d
To conrm the change and exit from the Control Menu please
Pour régler une demi-fonction
1. CHECK WATER CONNECTION
2. SWITCH ON THE DISHWASHER
3.
4.
LOAD THE RACKS (see LOADING THE RACKS)
FILLING THE DETERGENT DISPENSER
(see PROGRAMS TABLE).
5.
6.
7.
CHOOSE THE PROGRAM AND CUSTOMISE THE CYCLE
(see PROGRAMS
DESCRIPTION)
(see OPTIONS AND FUNCTIONS)
START
END OF WASH CYCLE
ashing of the wash cycle number on the display. Open the
The machine will switch off automatically during certain
extended periods of inactivity, in order to minimise electri-
city consumption. If the crockery is only lightly soiled or
if it has been rinsed with water before being placed in the
dishwasher, reduce the amount of detergent used accordingly.
MODIFYING A RUNNING PROGRAM
ON/OFF
ON/OFF
the new wash cycle and any desired options; Start the wash cycle
START/Pause
ADDING EXTRA CROCKERY
START/Pause
be ware of HOT steam!
START/Pause
ACCIDENTAL INTERRUPTIONS
START/Pause
DAILY USE
1. ECO - Normally soiled crockery. Standard program, the most efficient in terms of its combined energy and water
consumption.
2. NORMAL - Mixed soil. For normally soiled dishes with dried food residues.
3. INTENSIVE - Program recommended for heavily soiled crockery, especially suitable for pans and saucepans (not to be used
for delicate items).
4. PRE-WASH - Use to refresh crockery planned to be washed later. No detergent to be used with this program.
5. FAST - Normally soiled crockery. Everyday cycle, that ensures optimal cleaning performance in shorter time.
6. SANITIZING - Normally or heavily soiled crockery, with additional antibacterial wash. Can be used to perform
maintenance of the dishwasher.
7. SELF- CLEAN - Program to be used to perform maintenance of the dishwasher. It cleans the interior of the appliance
using hot water.
(see CONTROL PANEL)
If an option is not compatible with the selected program see PROGRAMS TABLE, the corresponding LED ฀ ฀ ฀ ฀rapidly 3 times
and beeps will sound. The option will not be enabled.
HALF LOAD
Remember to halve the amount of detergent.
The DELAY function cannot be set once a wash cycle
has been started.
TABLET (Tab)
If you use powder or liquid detergent, this option
should be off.
E d
To conrm the change and exit from the Control Menu please
Pour régler une fonction multiple
Les fonctions peuvent être sélectionnées directement en
appuyant sur la touche correspondante(voir PANNEAU DE
COMMANDE).
Si une fonction n'est pas compatible avec le programme
sélectionné voir TABLEAU DES PROGRAMMES, le voyant
correspondant clignote 3 fois et un signal sonore se fait
entendre. La fonction n'est pas activée.