EasyManuals Logo

IKEA RENGORA Instruction Manual

IKEA RENGORA
28 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #6 background imageLoading...
Page #6 background image
To download the full version visit www.ikea.com
6ENGLISH
Product description
1
Upper rack
2
Foldableaps
3
Upperrackheightadjuster
4
Uppersprayerarm
5
Lower rack
6
Cutlerybasket
7
Lowersprayerarm
8
FilterAssembly
9
Saltreservoir
10
DetergentandRinseAiddispensers
11
Control pannel
First Use
Advice regarding the rst time use
Beforeinstallationandrstusageoftheappliancepleaseread
carefully„SAFETYINSTRUCTION”and„ASSEMBLYINSTRUCTION”
availableintheproductliteraturebag.Pleaserememberto
removealltransportprotectionpartsfromthedishwasher.
Filling the salt reservoir
TheuseofsaltpreventstheformationofLIMESCALEonthe
dishesandonthemachine’sfunctionalcomponents.
ItismandatorythatTHE SALT RESERVOIR BE NEVER EMPTY.
Itisimportanttosetthewaterhardness.
Thesaltreservoirislocatedinthelowerpartofthedishwasher
(seePRODUCTDESCRIPTION)andshouldbelledwhenthe
SALTREFILLindicatorlight
1. Upper rack
2. ฀฀฀฀฀฀฀
3. Upper rack height adjuster
4. Upper sprayer arm
5. Lower rack
6. Cutlery basket
7. Lower sprayer arm
8. Filter Assembly
9. Salt reservoir
10. Detergent and Rinse Aid dispensers
11. Rating plate
12. Control panel
ADVICE REGARDING THE FIRST TIME USE
After installation, remove the stoppers from the racks and the
retaining elastic elements from the upper rack.
FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on the
dishes andon the machine’s functional components.
It is important that the salt reservoir be never empty.
It is important to set the water hardness.
The salt reservoir is located in the lower part of the
dishwasher (see PRODUCT DESCRIPTION) and should be
filled when the SALT REFILL indicator light in the
control panel is lit .
1. Remove the lower rack and
unscrew the reservoir cap
(anticlockwise).
2. Only the first time you do this: fill
the salt reservoir with water.
3. Position the funnel (see figure)
and fill the salt reservoir right up
to its edge (approximately 1 kg);
it is not unusual for a little water to
leak out.
4. Remove the funnel and wipe any
salt residue away from the
opening.
1. On-Off/Reset button with indicator light
2. Program selection button
3. Salt refill indicator ligh
4. Rinse Aid refill indicator ligh
5. Program number and delay time indicator
6. Tablet indicator light
7. Display
8. Half Load indicator light
9. Half Load button
10. Delay button
11. START/Pause button with indicator light / Tab
1 2 3 4 5 6 7 8 9 10
11
inthecontrolpanelislit.
1. Removethelowerrackandunscrew
thereservoircap(anticlockwise).
2. Positionthefunnel(seegure)and
llthesaltreservoirrightuptoits
edge(approximately1kg);itisnot
unusualforalittlewatertoleakout.
3. Only the rst time you do this: ll
the salt reservoir with water.
4. Removethefunnelandwipeany
saltresidueawayfromtheopening.
1. Upper rack
2. ฀฀฀฀฀฀฀
3. Upper rack height adjuster
4. Upper sprayer arm
5. Lower rack
6. Cutlery basket
7. Lower sprayer arm
8. Filter Assembly
9. Salt reservoir
10. Detergent and Rinse Aid dispensers
11. Rating plate
12. Control panel
ADVICE REGARDING THE FIRST TIME USE
After installation, remove the stoppers from the racks and the
retaining elastic elements from the upper rack.
FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on the
dishes andon the machine’s functional components.
It is important that the salt reservoir be never empty.
It is important to set the water hardness.
The salt reservoir is located in the lower part of the
dishwasher (see PRODUCT DESCRIPTION) and should be
filled when the SALT REFILL indicator light in the
control panel is lit .
1. Remove the lower rack and
unscrew the reservoir cap
(anticlockwise).
2. Only the first time you do this: fill
the salt reservoir with water.
3. Position the funnel (see figure)
and fill the salt reservoir right up
to its edge (approximately 1 kg);
it is not unusual for a little water to
leak out.
4. Remove the funnel and wipe any
salt residue away from the
opening.
1. On-Off/Reset button with indicator light
2. Program selection button
3. Salt refill indicator ligh
4. Rinse Aid refill indicator ligh
5. Program number and delay time indicator
6. Tablet indicator light
7. Display
8. Half Load indicator light
9. Half Load button
10. Delay button
11. START/Pause button with indicator light / Tab
1 2 3 4 5 6 7 8 9 10
11
2
2
1
5
4
3
6
1011
12
0000 000 00000
Service:
7
8
9
11
Makesurethecapisscrewedontightly,sothatnodetergent
cangetintothecontainerduringthewashprogram(thiscould
damagethewatersoftenerbeyondrepair).
Assoonasthisprocedureiscomplete,runaprogramwithout
loading.
Only use salt that has been specically designed for
dishwashers. If the salt container is not lled, the water
softener and the heating element may be damaged
as a result of limescale accumulation. Using of Salt is
recommended with any type of dishwasher detergent.
Whenever you need to add salt, it is mandatory to complete
the procedure before the beginning of the washing cycle to
avoid corrosion.
Setting the water hardness
Toallowthewatersoftenertoworkinaperfectway,itis
essentialthatthewaterhardnesssettingisbasedontheactual
waterhardnessinyourhouse.Thisinformationcanbeobtained
fromyourlocalwatersupplier.Thefactorysetsthedefaultvalue
forthewaterhardness.
SwitchontheappliancebypressingtheON/OFFbutton.
SwitchotheappliancebypressingtheON/OFFbutton.
Hold down button
Switch on the appliance by pressing the ON/OFF button.
Switch off the appliance by pressing the ON/OFF button.
Hold down button
for 5 seconds, until you hear a beep.
Switch on the appliance by pressing the ON/OFF button.
The current selection level number and the salt indicator light
฀฀฀฀฀฀
Press button to select the desired hardness level (see
WATER HARDNESS TABLE).
Switch off the appliance by pressing the ON/OFF button.
Setting is complete!
Water Hardness Table
Level
°dH
German degrees
°fH
French degrees
1 Soft 0 - 6 0 - 10
2 Medium 7 - 11 11 - 20
3 Average 12 - 17 21 - 30
4 Hard 18 - 34 31 - 60
5 Very hard 35 - 50 61 - 90
Make sure the cap is screwed on tightly, so that no detergent can
get into the container during the wash program (this could damage
the water softener beyond repair).
As soon as this procedure is complete, run a program without
loading. The “Pre-Wash” program alone is NOT฀฀฀฀฀฀
Residual saline solution or grains of salt can lead to corrosion,
irreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such
circumstances.
฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀s.
฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀
heating element may be damaged as a result.
Whenever you need to add salt, it is mandatory to complete
the procedure before the beginning of the washing cycle.
SETTING THE WATER HARDNESS
To allow the water softener to work in a perfect way, it is essential
that the water hardness setting is based on the actual water hard-
ness in your house. This information can be obtained from your local
water supplier. The factory setting is for average (3) water hardness.
FILLING THE RINSE AID DISPENSER
A
should be lled when the RINSE AID REFILL indicator light
B
(110 ml) reference notch of the lling space - avoid spilling it.
NEVER pour the rinse aid directly into the tub.
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satised with the drying results, you can
The current selection level number and rinse aid indicator light ash.
the dishwasher model. The factory setting is specic to the model,
FILLING THE DETERGENT DISPENSER
฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀
dishwashers.
useof detergent, rinse aid liquid and rened salt is required.
To open the detergent dispenser
press button A.
Introduce the detergent into
the dry dispenser B only.
Place the amount of detergent
for pre-washing directly inside
the tub.
A
B
B
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the TABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
for5seconds,untilyouhearabeep.
SwitchontheappliancebypressingquicklytheON/OFF
button.
Thecurrentselectionlevelnumberandthesaltindicatorlight
bothash
Pressbutton
Switch on the appliance by pressing the ON/OFF button.
Switch off the appliance by pressing the ON/OFF button.
Hold down button
for 5 seconds, until you hear a beep.
Switch on the appliance by pressing the ON/OFF button.
The current selection level number and the salt indicator light
฀฀฀฀฀฀
Press button to select the desired hardness level (see
WATER HARDNESS TABLE).
Switch off the appliance by pressing the ON/OFF button.
Setting is complete!
Water Hardness Table
Level
°dH
German degrees
°fH
French degrees
1 Soft 0 - 6 0 - 10
2 Medium 7 - 11 11 - 20
3 Average 12 - 17 21 - 30
4 Hard 18 - 34 31 - 60
5 Very hard 35 - 50 61 - 90
Make sure the cap is screwed on tightly, so that no detergent can
get into the container during the wash program (this could damage
the water softener beyond repair).
As soon as this procedure is complete, run a program without
loading. The “Pre-Wash” program alone is NOT฀฀฀฀฀฀
Residual saline solution or grains of salt can lead to corrosion,
irreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such
circumstances.
฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀s.
฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀
heating element may be damaged as a result.
Whenever you need to add salt, it is mandatory to complete
the procedure before the beginning of the washing cycle.
SETTING THE WATER HARDNESS
To allow the water softener to work in a perfect way, it is essential
that the water hardness setting is based on the actual water hard-
ness in your house. This information can be obtained from your local
water supplier. The factory setting is for average (3) water hardness.
FILLING THE RINSE AID DISPENSER
A
should be lled when the RINSE AID REFILL indicator light
B
(110 ml) reference notch of the lling space - avoid spilling it.
NEVER pour the rinse aid directly into the tub.
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satised with the drying results, you can
The current selection level number and rinse aid indicator light ash.
the dishwasher model. The factory setting is specic to the model,
FILLING THE DETERGENT DISPENSER
฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀
dishwashers.
useof detergent, rinse aid liquid and rened salt is required.
To open the detergent dispenser
press button A.
Introduce the detergent into
the dry dispenser B only.
Place the amount of detergent
for pre-washing directly inside
the tub.
A
B
B
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the TABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
toselectthedesiredhardnesslevel(see
WATERHARDNESSTABLE).
SwitchotheappliancebypressingtheON/OFFbutton.
Settingiscomplete!
WaterHardnessTable
Level °dH
German
degrees
°fH
French
degrees
°Clark
English
degrees
1 Soft 0 - 6 0 - 10 0 - 7
2 Medium 7 - 11 11 - 20 8 - 14
3 Average 12 - 16 21 - 29 15 - 20
4 Hard 17 - 34 30 - 60 21 - 42
5 Veryhard 35 - 50 61 - 90 43 - 62
Water Softening System
Watersoftenerautomaticallyreduceswaterhardness,conse-
quentlypreventingscalebuilduponheater,contributingalso
tobettercleaningeciency.Thissystemregeneratesitselfwith
salt,thereforeitisrequiredtorellsaltcontainerwhenempty.
Frequencyofregenerationdependsonwaterhardnesslevel
setting-regenerationtakesplaceonceper5Ecocycleswith
waterhardnesslevelsetto3.
Regenerationprocessstartsinnalrinseandnishesindrying
phase,beforecycleends.
*Singleregenerationconsumes:~3.5Lofwater;
*Takesupto5additionalminutesforthecycle;
*Consumesbelow0.005kWhofenergy.

Other manuals for IKEA RENGORA

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the IKEA RENGORA and is the answer not in the manual?

IKEA RENGORA Specifications

General IconGeneral
Capacity13 Place Settings
Number of Programs5
Delay StartYes
Child LockYes
TypeBuilt-in

Related product manuals