IKEA RENGORA - Page 18

Per scaricare la versione completa visita il sito www.ikea.com
18ITALIANO
Funzioni
NATURALDRY
Il sistema NaturalDry è una funzione di asciugatura a convezione che
apre automaticamente la porta durante/dopo la fase di asciugatura
per garantire stoviglie perfettamente asciutte dopo ogni lavaggio.
La porta viene aperta quando la temperatura è tale da non poter
danneggiare i mobili della cucina.
Non tirare fuori le stoviglie subito dopo l'apertura della porta, ma
attendere per un'asciugatura adeguata.
La funzione non può essere attivata per tutti i programmi, fare
riferimento alla tabella dei programmi.
Come ulteriore protezione dal vapore, la lavastoviglie viene fornita
con una speciale lamina di protezione aggiuntiva. Per istruzioni
sul montaggio della lamina protettiva, vedere le (ISTRUZIONI DI
MONTAGGIO).
La funzione NaturalDry può essere disabilitata come segue:
1. Accedere al menu del software della lavastoviglie premendo a
lungo il tasto
• Switch on the appliance by pressing the ON/OFF button.
• Switch off the appliance by pressing the ON/OFF button.
• Hold down button
for 5 seconds, until you hear a beep.
• Switch on the appliance by pressing the ON/OFF button.
•
•
The current selection level number and the salt indicator light
฀฀฀฀฀฀
Press button to select the desired hardness level (see
WATER HARDNESS TABLE).
• Switch off the appliance by pressing the ON/OFF button.
Setting is complete!
Water Hardness Table
Level
°dH
German degrees
°fH
French degrees
1 Soft 0 - 6 0 - 10
2 Medium 7 - 11 11 - 20
3 Average 12 - 17 21 - 30
4 Hard 18 - 34 31 - 60
5 Very hard 35 - 50 61 - 90
Make sure the cap is screwed on tightly, so that no detergent can
get into the container during the wash program (this could damage
the water softener beyond repair).
As soon as this procedure is complete, run a program without
loading. The “Pre-Wash” program alone is NOT฀฀฀฀฀฀
Residual saline solution or grains of salt can lead to corrosion,
irreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such
circumstances.
฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀s.
฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀
heating element may be damaged as a result.
Whenever you need to add salt, it is mandatory to complete
the procedure before the beginning of the washing cycle.
SETTING THE WATER HARDNESS
To allow the water softener to work in a perfect way, it is essential
that the water hardness setting is based on the actual water hard-
ness in your house. This information can be obtained from your local
water supplier. The factory setting is for average (3) water hardness.
FILLING THE RINSE AID DISPENSER
A
should be lled when the RINSE AID REFILL indicator light
B
(110 ml) reference notch of the lling space - avoid spilling it.
NEVER pour the rinse aid directly into the tub.
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satised with the drying results, you can
The current selection level number and rinse aid indicator light ash.
the dishwasher model. The factory setting is specic to the model,
FILLING THE DETERGENT DISPENSER
฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀
dishwashers.
useof detergent, rinse aid liquid and rened salt is required.
To open the detergent dispenser
press button A.
Introduce the detergent into
the dry dispenser B only.
Place the amount of detergent
for pre-washing directly inside
the tub.
A
B
B
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the TABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
(6 secondi).
2. Accedendo al menu di controllo NaturalDry è possibile cambiare
lo stato della funzione premendo il tasto
• Switch on the appliance by pressing the ON/OFF button.
• Switch off the appliance by pressing the ON/OFF button.
• Hold down button
for 5 seconds, until you hear a beep.
• Switch on the appliance by pressing the ON/OFF button.
•
•
The current selection level number and the salt indicator light
฀฀฀฀฀฀
Press button to select the desired hardness level (see
WATER HARDNESS TABLE).
• Switch off the appliance by pressing the ON/OFF button.
Setting is complete!
Water Hardness Table
Level
°dH
German degrees
°fH
French degrees
1 Soft 0 - 6 0 - 10
2 Medium 7 - 11 11 - 20
3 Average 12 - 17 21 - 30
4 Hard 18 - 34 31 - 60
5 Very hard 35 - 50 61 - 90
Make sure the cap is screwed on tightly, so that no detergent can
get into the container during the wash program (this could damage
the water softener beyond repair).
As soon as this procedure is complete, run a program without
loading. The “Pre-Wash” program alone is NOT฀฀฀฀฀฀
Residual saline solution or grains of salt can lead to corrosion,
irreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such
circumstances.
฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀s.
฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀
heating element may be damaged as a result.
Whenever you need to add salt, it is mandatory to complete
the procedure before the beginning of the washing cycle.
SETTING THE WATER HARDNESS
To allow the water softener to work in a perfect way, it is essential
that the water hardness setting is based on the actual water hard-
ness in your house. This information can be obtained from your local
water supplier. The factory setting is for average (3) water hardness.
FILLING THE RINSE AID DISPENSER
A
should be lled when the RINSE AID REFILL indicator light
B
(110 ml) reference notch of the lling space - avoid spilling it.
NEVER pour the rinse aid directly into the tub.
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satised with the drying results, you can
The current selection level number and rinse aid indicator light ash.
the dishwasher model. The factory setting is specic to the model,
FILLING THE DETERGENT DISPENSER
฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀
dishwashers.
useof detergent, rinse aid liquid and rened salt is required.
To open the detergent dispenser
press button A.
Introduce the detergent into
the dry dispenser B only.
Place the amount of detergent
for pre-washing directly inside
the tub.
A
B
B
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the TABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
:
E – funzione abilitata d – funzione disabilitata
Per confermare la modica e uscire dal menu di controllo,
premere a lungo il tasto
• Switch on the appliance by pressing the ON/OFF button.
• Switch off the appliance by pressing the ON/OFF button.
• Hold down button
for 5 seconds, until you hear a beep.
• Switch on the appliance by pressing the ON/OFF button.
•
•
The current selection level number and the salt indicator light
฀฀฀฀฀฀
Press button to select the desired hardness level (see
WATER HARDNESS TABLE).
• Switch off the appliance by pressing the ON/OFF button.
Setting is complete!
Water Hardness Table
Level
°dH
German degrees
°fH
French degrees
1 Soft 0 - 6 0 - 10
2 Medium 7 - 11 11 - 20
3 Average 12 - 17 21 - 30
4 Hard 18 - 34 31 - 60
5 Very hard 35 - 50 61 - 90
Make sure the cap is screwed on tightly, so that no detergent can
get into the container during the wash program (this could damage
the water softener beyond repair).
As soon as this procedure is complete, run a program without
loading. The “Pre-Wash” program alone is NOT฀฀฀฀฀฀
Residual saline solution or grains of salt can lead to corrosion,
irreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such
circumstances.
฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀s.
฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀
heating element may be damaged as a result.
Whenever you need to add salt, it is mandatory to complete
the procedure before the beginning of the washing cycle.
SETTING THE WATER HARDNESS
To allow the water softener to work in a perfect way, it is essential
that the water hardness setting is based on the actual water hard-
ness in your house. This information can be obtained from your local
water supplier. The factory setting is for average (3) water hardness.
FILLING THE RINSE AID DISPENSER
A
should be lled when the RINSE AID REFILL indicator light
B
(110 ml) reference notch of the lling space - avoid spilling it.
NEVER pour the rinse aid directly into the tub.
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satised with the drying results, you can
The current selection level number and rinse aid indicator light ash.
the dishwasher model. The factory setting is specic to the model,
FILLING THE DETERGENT DISPENSER
฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀฀
dishwashers.
useof detergent, rinse aid liquid and rened salt is required.
To open the detergent dispenser
press button A.
Introduce the detergent into
the dry dispenser B only.
Place the amount of detergent
for pre-washing directly inside
the tub.
A
B
B
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the TABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
(3 sec).
La misurazione dei dati per il programma ECO avviene in condizioni di laboratorio secondo quanto prescritto dalla norma europea EN
60436:2019.
Nota per i laboratori di prova: per informazioni comparative sulle condizioni delle prove EN, inviare una email al seguente indirizzo: dw_test_
support@whirlpool.com
Questi programmi non richiedono un pre-trattamento delle stoviglie.
*) Non è possibile selezionare tutte le opzioni contemporaneamente.
**)AdeccezionedelprogrammaEco,ivaloririportatiperglialtriprogrammisonopuramenteindicativi.Ladurataeettivapuòdipendereda
molti fattori, quali la temperatura e la pressione dell'acqua di alimentazione, la temperatura ambiente, la dose di detersivo utilizzata, la quantità
e il tipo di carico e il suo bilanciamento, la selezione di determinate opzioni e la taratura dei sensori.
1. ECO -IlprogrammaEcoèindicatoperlestovigliemediamentesporche;èilprogrammapiùecienteinterminidiconsumocombinatodi
acqua ed energia e viene usato per valutare la conformità dell'apparecchio alla legislazione UE in materia di progettazione ecocompatibile.
2. LAVAGGIO E ASCIUGATURA CONVENZIONALE - Stoviglie mediamente sporche. Per piatti con sporco normale e residui secchi di cibo.
3. INTENSIVO - Programma indicato per stoviglie molto sporche, consigliato specialmente per pentole e tegami. Da non usare per stoviglie
delicate.
4. LAVAGGIO RAPIDO - Programma per una quantità limitata di stoviglie mediamente sporche. Permette di ottenere un risultato di lavaggio
Programma
Fase di
asciu-
gatura
Natural
Dry
Funzioni
disponibili
(*)
Durata del
programma
(h:min)**)
Consumo
d'acqua
(litri/ciclo)
Consumo
energetico
(kWh/ciclo)
1 Eco
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
has been started.
NaturalDry
(INSTALLATION GUIDE)
E d
To conrm the change and exit from the Control Menu please
DELAY
1 12
Duration of
(h:min)
**)
(litres/cycle) (kWh/cycle)
50°
2:45 12.0 0.92
1
Eco
2
Conventional
wash and dry
55° 2:00 15.0 1.35
3
Intensive 65°
- 2:30 15.0 1.50
4
Fast 50°
-
- 0:55 11.5 1.10
5
Sanitizing 65°
- 1:40 11.5 1.30
6
Pre-Wash
-
-
- 0:10 4.5 0.01
7
Self-Clean 65°
-
-
0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
50°
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
has been started.
NaturalDry
(INSTALLATION GUIDE)
E d
To conrm the change and exit from the Control Menu please
DELAY
1 12
Duration of
(h:min)
**)
(litres/cycle) (kWh/cycle)
50°
2:45 12.0 0.92
1
Eco
2
Conventional
wash and dry
55° 2:00 15.0 1.35
3
Intensive 65°
- 2:30 15.0 1.50
4
Fast 50°
-
- 0:55 11.5 1.10
5
Sanitizing 65°
- 1:40 11.5 1.30
6
Pre-Wash
-
-
- 0:10 4.5 0.01
7
Self-Clean 65°
-
-
0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
has been started.
NaturalDry
(INSTALLATION GUIDE)
E d
To conrm the change and exit from the Control Menu please
DELAY
1 12
Duration of
(h:min)
**)
(litres/cycle) (kWh/cycle)
50°
2:45 12.0 0.92
1
Eco
2
Conventional
wash and dry
55° 2:00 15.0 1.35
3
Intensive 65°
- 2:30 15.0 1.50
4
Fast 50°
-
- 0:55 11.5 1.10
5
Sanitizing 65°
- 1:40 11.5 1.30
6
Pre-Wash
-
-
- 0:10 4.5 0.01
7
Self-Clean 65°
-
-
0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
has been started.
NaturalDry
(INSTALLATION GUIDE)
E d
To conrm the change and exit from the Control Menu please
DELAY
1 12
Duration of
(h:min)
**)
(litres/cycle) (kWh/cycle)
50°
2:45 12.0 0.92
1
Eco
2
Conventional
wash and dry
55° 2:00 15.0 1.35
3
Intensive 65°
- 2:30 15.0 1.50
4
Fast 50°
-
- 0:55 11.5 1.10
5
Sanitizing 65°
- 1:40 11.5 1.30
6
Pre-Wash
-
-
- 0:10 4.5 0.01
7
Self-Clean 65°
-
-
0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
2:45 12.0 0.94
2 Lavaggio e
asciugatura
convenzionali
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
has been started.
NaturalDry
(INSTALLATION GUIDE)
E d
To conrm the change and exit from the Control Menu please
DELAY
1 12
Duration of
(h:min)
**)
(litres/cycle) (kWh/cycle)
50°
2:45 12.0 0.92
1
Eco
2
Conventional
wash and dry
55° 2:00 15.0 1.35
3
Intensive 65°
- 2:30 15.0 1.50
4
Fast 50°
-
- 0:55 11.5 1.10
5
Sanitizing 65°
- 1:40 11.5 1.30
6
Pre-Wash
-
-
- 0:10 4.5 0.01
7
Self-Clean 65°
-
-
0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
55°
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
has been started.
NaturalDry
(INSTALLATION GUIDE)
E d
To conrm the change and exit from the Control Menu please
DELAY
1 12
Duration of
(h:min)
**)
(litres/cycle) (kWh/cycle)
50°
2:45 12.0 0.92
1
Eco
2
Conventional
wash and dry
55° 2:00 15.0 1.35
3
Intensive 65°
- 2:30 15.0 1.50
4
Fast 50°
-
- 0:55 11.5 1.10
5
Sanitizing 65°
- 1:40 11.5 1.30
6
Pre-Wash
-
-
- 0:10 4.5 0.01
7
Self-Clean 65°
-
-
0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
has been started.
NaturalDry
(INSTALLATION GUIDE)
E d
To conrm the change and exit from the Control Menu please
DELAY
1 12
Duration of
(h:min)
**)
(litres/cycle) (kWh/cycle)
50°
2:45 12.0 0.92
1
Eco
2
Conventional
wash and dry
55° 2:00 15.0 1.35
3
Intensive 65°
- 2:30 15.0 1.50
4
Fast 50°
-
- 0:55 11.5 1.10
5
Sanitizing 65°
- 1:40 11.5 1.30
6
Pre-Wash
-
-
- 0:10 4.5 0.01
7
Self-Clean 65°
-
-
0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
has been started.
NaturalDry
(INSTALLATION GUIDE)
E d
To conrm the change and exit from the Control Menu please
DELAY
1 12
Duration of
(h:min)
**)
(litres/cycle) (kWh/cycle)
50°
2:45 12.0 0.92
1
Eco
2
Conventional
wash and dry
55° 2:00 15.0 1.35
3
Intensive 65°
- 2:30 15.0 1.50
4
Fast 50°
-
- 0:55 11.5 1.10
5
Sanitizing 65°
- 1:40 11.5 1.30
6
Pre-Wash
-
-
- 0:10 4.5 0.01
7
Self-Clean 65°
-
-
0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
2:00 15.0 1.35
3 Intensivo
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
has been started.
NaturalDry
(INSTALLATION GUIDE)
E d
To conrm the change and exit from the Control Menu please
DELAY
1 12
Duration of
(h:min)
**)
(litres/cycle) (kWh/cycle)
50°
2:45 12.0 0.92
1
Eco
2
Conventional
wash and dry
55° 2:00 15.0 1.35
3
Intensive 65°
- 2:30 15.0 1.50
4
Fast 50°
-
- 0:55 11.5 1.10
5
Sanitizing 65°
- 1:40 11.5 1.30
6
Pre-Wash
-
-
- 0:10 4.5 0.01
7
Self-Clean 65°
-
-
0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
65°
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
has been started.
NaturalDry
(INSTALLATION GUIDE)
E d
To conrm the change and exit from the Control Menu please
DELAY
1 12
Duration of
(h:min)
**)
(litres/cycle) (kWh/cycle)
50°
2:45 12.0 0.92
1
Eco
2
Conventional
wash and dry
55° 2:00 15.0 1.35
3
Intensive 65°
- 2:30 15.0 1.50
4
Fast 50°
-
- 0:55 11.5 1.10
5
Sanitizing 65°
- 1:40 11.5 1.30
6
Pre-Wash
-
-
- 0:10 4.5 0.01
7
Self-Clean 65°
-
-
0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
has been started.
NaturalDry
(INSTALLATION GUIDE)
E d
To conrm the change and exit from the Control Menu please
DELAY
1 12
Duration of
(h:min)
**)
(litres/cycle) (kWh/cycle)
50°
2:45 12.0 0.92
1
Eco
2
Conventional
wash and dry
55° 2:00 15.0 1.35
3
Intensive 65°
- 2:30 15.0 1.50
4
Fast 50°
-
- 0:55 11.5 1.10
5
Sanitizing 65°
- 1:40 11.5 1.30
6
Pre-Wash
-
-
- 0:10 4.5 0.01
7
Self-Clean 65°
-
-
0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
has been started.
NaturalDry
(INSTALLATION GUIDE)
E d
To conrm the change and exit from the Control Menu please
DELAY
1 12
Duration of
(h:min)
**)
(litres/cycle) (kWh/cycle)
50°
2:45 12.0 0.92
1
Eco
2
Conventional
wash and dry
55° 2:00 15.0 1.35
3
Intensive 65°
- 2:30 15.0 1.50
4
Fast 50°
-
- 0:55 11.5 1.10
5
Sanitizing 65°
- 1:40 11.5 1.30
6
Pre-Wash
-
-
- 0:10 4.5 0.01
7
Self-Clean 65°
-
-
0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
2:30 15.0 1.50
4 Lavaggio rapido
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
has been started.
NaturalDry
(INSTALLATION GUIDE)
E d
To conrm the change and exit from the Control Menu please
DELAY
1 12
Duration of
(h:min)
**)
(litres/cycle) (kWh/cycle)
50°
2:45 12.0 0.92
1
Eco
2
Conventional
wash and dry
55°
2:00 15.0 1.35
3
Intensive 65°
- 2:30 15.0 1.50
4
Fast 50°
-
- 0:55 11.5 1.10
5
Sanitizing 65°
- 1:40 11.5 1.30
6
Pre-Wash
-
-
- 0:10 4.5 0.01
7
Self-Clean 65°
-
-
0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
50° - -
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
has been started.
NaturalDry
(INSTALLATION GUIDE)
E d
To conrm the change and exit from the Control Menu please
DELAY
1 12
Duration of
(h:min)
**)
(litres/cycle) (kWh/cycle)
50°
2:45 12.0 0.92
1
Eco
2
Conventional
wash and dry
55°
2:00 15.0 1.35
3
Intensive 65°
- 2:30 15.0 1.50
4
Fast 50°
-
- 0:55 11.5 1.10
5
Sanitizing 65°
- 1:40 11.5 1.30
6
Pre-Wash
-
-
- 0:10 4.5 0.01
7
Self-Clean 65°
-
-
0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
0:55 11.5 1.10
5 Igienizzante
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
has been started.
NaturalDry
(INSTALLATION GUIDE)
E d
To conrm the change and exit from the Control Menu please
DELAY
1 12
Duration of
(h:min)
**)
(litres/cycle) (kWh/cycle)
50°
2:45 12.0 0.92
1
Eco
2
Conventional
wash and dry
55° 2:00 15.0 1.35
3
Intensive 65°
- 2:30 15.0 1.50
4
Fast 50°
-
- 0:55 11.5 1.10
5
Sanitizing 65°
- 1:40 11.5 1.30
6
Pre-Wash
-
-
- 0:10 4.5 0.01
7
Self-Clean 65°
-
-
0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
65°
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
has been started.
NaturalDry
(INSTALLATION GUIDE)
E d
To conrm the change and exit from the Control Menu please
DELAY
1 12
Duration of
(h:min)
**)
(litres/cycle) (kWh/cycle)
50°
2:45 12.0 0.92
1
Eco
2
Conventional
wash and dry
55° 2:00 15.0 1.35
3
Intensive 65°
- 2:30 15.0 1.50
4
Fast 50°
-
- 0:55 11.5 1.10
5
Sanitizing 65°
- 1:40 11.5 1.30
6
Pre-Wash
-
-
- 0:10 4.5 0.01
7
Self-Clean 65°
-
-
0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
-
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
has been started.
NaturalDry
(INSTALLATION GUIDE)
E d
To conrm the change and exit from the Control Menu please
DELAY
1 12
Duration of
(h:min)
**)
(litres/cycle) (kWh/cycle)
50°
2:45 12.0 0.92
1
Eco
2
Conventional
wash and dry
55° 2:00 15.0 1.35
3
Intensive 65°
- 2:30 15.0 1.50
4
Fast 50°
-
- 0:55 11.5 1.10
5
Sanitizing 65°
- 1:40 11.5 1.30
6
Pre-Wash
-
-
- 0:10 4.5 0.01
7
Self-Clean 65°
-
-
0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
1:40 11.5 1.30
6 Pre-lavaggio
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
has been started.
NaturalDry
(INSTALLATION GUIDE)
E d
To conrm the change and exit from the Control Menu please
DELAY
1 12
Duration of
(h:min)
**)
(litres/cycle) (kWh/cycle)
50°
2:45 12.0 0.92
1
Eco
2
Conventional
wash and dry
55° 2:00 15.0 1.35
3
Intensive 65°
- 2:30 15.0 1.50
4
Fast 50°
-
- 0:55 11.5 1.10
5
Sanitizing 65°
- 1:40 11.5 1.30
6
Pre-Wash
-
-
- 0:10 4.5 0.01
7
Self-Clean 65°
-
-
0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
- - -
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
has been started.
NaturalDry
(INSTALLATION GUIDE)
E d
To conrm the change and exit from the Control Menu please
DELAY
1 12
Duration of
(h:min)
**)
(litres/cycle) (kWh/cycle)
50°
2:45 12.0 0.92
1
Eco
2
Conventional
wash and dry
55° 2:00 15.0 1.35
3
Intensive 65°
- 2:30 15.0 1.50
4
Fast 50°
-
- 0:55 11.5 1.10
5
Sanitizing 65°
- 1:40 11.5 1.30
6
Pre-Wash
-
-
- 0:10 4.5 0.01
7
Self-Clean 65°
-
-
0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
0:10 4.5 0.01
7 Autopulente
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
has been started.
NaturalDry
(INSTALLATION GUIDE)
E d
To conrm the change and exit from the Control Menu please
DELAY
1 12
Duration of
(h:min)
**)
(litres/cycle) (kWh/cycle)
50°
2:45 12.0 0.92
1
Eco
2
Conventional
wash and dry
55° 2:00 15.0 1.35
3
Intensive 65°
- 2:30 15.0 1.50
4
Fast 50°
-
- 0:55 11.5 1.10
5
Sanitizing 65°
- 1:40 11.5 1.30
6
Pre-Wash
-
-
- 0:10 4.5 0.01
7
Self-Clean 65°
-
-
0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
65° - -
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
has been started.
NaturalDry
(INSTALLATION GUIDE)
E d
To conrm the change and exit from the Control Menu please
DELAY
1 12
Duration of
(h:min)
**)
(litres/cycle) (kWh/cycle)
50°
2:45 12.0 0.92
1
Eco
2
Conventional
wash and dry
55° 2:00 15.0 1.35
3
Intensive 65°
- 2:30 15.0 1.50
4
Fast 50°
-
- 0:55 11.5 1.10
5
Sanitizing 65°
- 1:40 11.5 1.30
6
Pre-Wash
-
-
- 0:10 4.5 0.01
7
Self-Clean 65°
-
-
0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
0:50 8.0 0.80
APERTURA PORTA
Eco 50° dopo 150 min
Lavaggio e asciugatura
convenzionali 55°
neciclo
Intensivo 65° neciclo
Lavaggio veloce 50° N/D
Igienizzante 65° N/D
Pre-lavaggio N/D
Auto-pulizia 65° N/D
Tabella dei programmi
appears on the display; each time you press the button,
The DELAY function cannot be set once a wash cycle
has been started.
NaturalDry
(INSTALLATION GUIDE)
E d
To conrm the change and exit from the Control Menu please
DELAY
1 12
Duration of
(h:min)
**)
(litres/cycle) (kWh/cycle)
50°
2:45 12.0 0.92
1
Eco
2
Conventional
wash and dry
55° 2:00 15.0 1.35
3
Intensive 65°
- 2:30 15.0 1.50
4
Fast 50°
-
- 0:55 11.5 1.10
5
Sanitizing 65°
- 1:40 11.5 1.30
6
Pre-Wash
-
-
- 0:10 4.5 0.01
7
Self-Clean 65°
-
-
0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
Impostazione della partenza ritardata
1. CHECK WATER CONNECTION
2. SWITCH ON THE DISHWASHER
3.
4.
LOAD THE RACKS (see LOADING THE RACKS)
FILLING THE DETERGENT DISPENSER
(see PROGRAMS TABLE).
5.
6.
7.
CHOOSE THE PROGRAM AND CUSTOMISE THE CYCLE
(see PROGRAMS
DESCRIPTION)
(see OPTIONS AND FUNCTIONS)
START
END OF WASH CYCLE
ashing of the wash cycle number on the display. Open the
The machine will switch off automatically during certain
extended periods of inactivity, in order to minimise electri-
city consumption. If the crockery is only lightly soiled or
if it has been rinsed with water before being placed in the
dishwasher, reduce the amount of detergent used accordingly.
MODIFYING A RUNNING PROGRAM
ON/OFF
ON/OFF
the new wash cycle and any desired options; Start the wash cycle
START/Pause
ADDING EXTRA CROCKERY
START/Pause
be ware of HOT steam!
START/Pause
ACCIDENTAL INTERRUPTIONS
START/Pause
DAILY USE
1. ECO - Normally soiled crockery. Standard program, the most efficient in terms of its combined energy and water
consumption.
2. NORMAL - Mixed soil. For normally soiled dishes with dried food residues.
3. INTENSIVE - Program recommended for heavily soiled crockery, especially suitable for pans and saucepans (not to be used
for delicate items).
4. PRE-WASH - Use to refresh crockery planned to be washed later. No detergent to be used with this program.
5. FAST - Normally soiled crockery. Everyday cycle, that ensures optimal cleaning performance in shorter time.
6. SANITIZING - Normally or heavily soiled crockery, with additional antibacterial wash. Can be used to perform
maintenance of the dishwasher.
7. SELF- CLEAN - Program to be used to perform maintenance of the dishwasher. It cleans the interior of the appliance
using hot water.
(see CONTROL PANEL)
If an option is not compatible with the selected program see PROGRAMS TABLE, the corresponding LED ฀ ฀ ฀ ฀rapidly 3 times
and beeps will sound. The option will not be enabled.
HALF LOAD
Remember to halve the amount of detergent.
The DELAY function cannot be set once a wash cycle
has been started.
TABLET (Tab)
If you use powder or liquid detergent, this option
should be off.
E d
To conrm the change and exit from the Control Menu please
Impostazione di una funzione a tempo
dimezzato
1. CHECK WATER CONNECTION
2. SWITCH ON THE DISHWASHER
3.
4.
LOAD THE RACKS (see LOADING THE RACKS)
FILLING THE DETERGENT DISPENSER
(see PROGRAMS TABLE).
5.
6.
7.
CHOOSE THE PROGRAM AND CUSTOMISE THE CYCLE
(see PROGRAMS
DESCRIPTION)
(see OPTIONS AND FUNCTIONS)
START
END OF WASH CYCLE
ashing of the wash cycle number on the display. Open the
The machine will switch off automatically during certain
extended periods of inactivity, in order to minimise electri-
city consumption. If the crockery is only lightly soiled or
if it has been rinsed with water before being placed in the
dishwasher, reduce the amount of detergent used accordingly.
MODIFYING A RUNNING PROGRAM
ON/OFF
ON/OFF
the new wash cycle and any desired options; Start the wash cycle
START/Pause
ADDING EXTRA CROCKERY
START/Pause
be ware of HOT steam!
START/Pause
ACCIDENTAL INTERRUPTIONS
START/Pause
DAILY USE
1. ECO - Normally soiled crockery. Standard program, the most efficient in terms of its combined energy and water
consumption.
2. NORMAL - Mixed soil. For normally soiled dishes with dried food residues.
3. INTENSIVE - Program recommended for heavily soiled crockery, especially suitable for pans and saucepans (not to be used
for delicate items).
4. PRE-WASH - Use to refresh crockery planned to be washed later. No detergent to be used with this program.
5. FAST - Normally soiled crockery. Everyday cycle, that ensures optimal cleaning performance in shorter time.
6. SANITIZING - Normally or heavily soiled crockery, with additional antibacterial wash. Can be used to perform
maintenance of the dishwasher.
7. SELF- CLEAN - Program to be used to perform maintenance of the dishwasher. It cleans the interior of the appliance
using hot water.
(see CONTROL PANEL)
If an option is not compatible with the selected program see PROGRAMS TABLE, the corresponding LED ฀ ฀ ฀ ฀rapidly 3 times
and beeps will sound. The option will not be enabled.
HALF LOAD
Remember to halve the amount of detergent.
The DELAY function cannot be set once a wash cycle
has been started.
TABLET (Tab)
If you use powder or liquid detergent, this option
should be off.
E d
To conrm the change and exit from the Control Menu please
Per impostare la funzione Multipastiglia
Le funzioni possono essere selezionate direttamente premendo
il tasto corrispondente (vedi PANNELLO DI CONTROLLO).
Se una funzione non è compatibile con il programma
selezionato (vedere TABELLA DEI PROGRAMMI), il LED
corrispondente lampeggia rapidamente 3 volte e viene
emesso un segnale acustico. La funzione non sarà attivata.