IMT 5525 User Manual (English)

Other manuals for IMT 5525

Manual126 pages

Parts & Specifications122 pages

Questions and Answers:

W
Warren KochAug 20, 2025
What to do if the winch on my IMT Construction Equipment will not lower?
- J
  Jonathan JohnsonAug 20, 2025
  If the winch on your IMT Construction Equipment is not lowering, first refer to the troubleshooting steps for 'Winch will not operate in either direction,' specifically items 1 through 5. If the issue persists, disconnect the brake line and cap both ends leading to the winch brake vent solenoid valve (Valve F). If the winch begins to lower, verify that Valve F is receiving power and inspect Valve F for contamination.
T
tammy57Aug 22, 2025
What to do if IMT Construction Equipment crane functions don't work?
- F
  flunaAug 22, 2025
  If the crane functions, such as boom down, extension out, and winch up, are not working, it may be due to a two-blocking or overload condition. To resolve this, winch down to relieve the two-block condition. Alternatively, boom up, extend in, or winch down to relieve the overload condition.
J
Janice MunozAug 26, 2025
What to do if my IMT Construction Equipment radio remote does not work?
- S
  Scott FoleyAug 26, 2025
  If the radio remote isn't functioning, it could be due to the emergency stop button being pushed in or a dead remote battery. Try pulling out the emergency stop button. If that doesn't work, replace the battery with a fully charged one.
L
Lisa WaltersAug 28, 2025
Why is my IMT Construction Equipment tethered remote not working?
- B
  Benjamin BarkerAug 28, 2025
  If the tethered remote isn't working, several factors could be the cause. First, ensure the “Power” toggle switch is switched to “Crane”. Also, verify the tether is securely plugged into the connection in the control cabinet. If the issue persists, the tethered control might be broken; in this case, use the buttons on the valve bank to manually stow the crane.
A
Aaron MendezAug 31, 2025
How to fix an IMT 5525 extend cylinder that will not extend?
- D
  derekcamposAug 31, 2025
  If the extend cylinder on your IMT Construction Equipment will not extend, start by reviewing items 1 through 3 in the troubleshooting guide for 'Winch will not operate in either direction'. Next, engage the extend on/off control valve (Valve C) manual override while attempting to extend. If the cylinder operates, verify that Valve C is receiving power and then inspect Valve C for contamination.
J
Joseph FosterSep 2, 2025
What should I do if the lower cylinder on my IMT 5525 Construction Equipment won't extend?
- S
  Shawn GarciaSep 3, 2025
  If the lower cylinder on your IMT Construction Equipment is not extending, begin by checking items 1 through 3 from the 'Winch will not operate in either direction' troubleshooting steps. Then, engage the lower on/off control valve (Valve D) manual override while operating the function. If the lower operates, verify that Valve D is receiving power and check Valve D for any contamination.
S
Sue HowardSep 5, 2025
Why is the extend cylinder on my IMT 5525 not retracting?
- N
  Natasha VasquezSep 5, 2025
  If the extend cylinder on your IMT Construction Equipment is not retracting, refer to items 1 and 2 from the 'Extend cylinder will not extend' troubleshooting guide. Also, check the extend counterbalance valve for contamination.
M
Michael WhiteSep 8, 2025
Why won't the lower cylinder retract on my IMT 5525?
- J
  jhowardSep 8, 2025
  If the lower cylinder on your IMT Construction Equipment is not retracting, check items 1 and 2 from the 'Lift cylinder will not extend' troubleshooting guide. Also, inspect the lower counterbalance valve for contamination.
D
Danny HudsonSep 12, 2025
What to do if my IMT Construction Equipment vehicle tires sink into the ground?
- M
  Monica MuellerSep 12, 2025
  If the vehicle tires are sinking into the ground, it is likely due to an unstable work area. Reposition the truck to more stable ground, or use blocks under the tires for added support.
A
Anita CooleySep 13, 2025
Why don't my hydraulic outrigger controls function on my IMT Construction Equipment?
- D
  Daniel MartinSep 13, 2025
  If the hydraulic outrigger controls aren't working, the crane may not have hydraulic power. Engage the PTO (Power Take-Off) to power the crane’s hydraulic system.