EasyManua.ls Logo

IMT 5525 - User Manual

Default Icon
126 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Printed on 21 June, 2007
Manual Part # 99903688
Model 5525-6025-6625 Parts &
Specifications
Manual Effective April 2005
Revision Date 20070621
IOWA MOLD TOOLING CO., INC.
PO Box 189
Garner, IA 50438
Tel: 641-923-3711 FAX: 641-923-2424
Website: http://www.imt.com
Copyright © 2007 Iowa Mold Tooling Co., Inc.
All rights reserved
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any
form or by any means, electronic, mechanical, photocopying, recording or otherwise without the
prior written permission of Iowa Mold Tooling Co., Inc.
Iowa Mold Tooling Co., Inc. is an Oshkosh Truck Corporation Company.
View thousands of Crane Specifications on FreeCraneSpecs.com
View thousands of Crane Specifications on FreeCraneSpecs.com

Table of Contents

Other manuals for IMT 5525

Preview: Operation?And Safety
Operation?And Safety118 pages
Preview: Parts & Specifications
Parts & Specifications122 pages

Questions and Answers

  • W
    Warren KochAug 20, 2025
    What to do if the winch on my IMT Construction Equipment will not lower?
    • J
      Jonathan JohnsonAug 20, 2025
      If the winch on your IMT Construction Equipment is not lowering, first refer to the troubleshooting steps for 'Winch will not operate in either direction,' specifically items 1 through 5. If the issue persists, disconnect the brake line and cap both ends leading to the winch brake vent solenoid valve (Valve F). If the winch begins to lower, verify that Valve F is receiving power and inspect Valve F for contamination.
  • T
    tammy57Aug 22, 2025
    What to do if IMT Construction Equipment crane functions don't work?
    • F
      flunaAug 22, 2025
      If the crane functions, such as boom down, extension out, and winch up, are not working, it may be due to a two-blocking or overload condition. To resolve this, winch down to relieve the two-block condition. Alternatively, boom up, extend in, or winch down to relieve the overload condition.
  • J
    Janice MunozAug 26, 2025
    What to do if my IMT Construction Equipment radio remote does not work?
    • S
      Scott FoleyAug 26, 2025
      If the radio remote isn't functioning, it could be due to the emergency stop button being pushed in or a dead remote battery. Try pulling out the emergency stop button. If that doesn't work, replace the battery with a fully charged one.
  • L
    Lisa WaltersAug 28, 2025
    Why is my IMT Construction Equipment tethered remote not working?
    • B
      Benjamin BarkerAug 28, 2025
      If the tethered remote isn't working, several factors could be the cause. First, ensure the “Power” toggle switch is switched to “Crane”. Also, verify the tether is securely plugged into the connection in the control cabinet. If the issue persists, the tethered control might be broken; in this case, use the buttons on the valve bank to manually stow the crane.
  • A
    Aaron MendezAug 31, 2025
    How to fix an IMT 5525 extend cylinder that will not extend?
    • D
      derekcamposAug 31, 2025
      If the extend cylinder on your IMT Construction Equipment will not extend, start by reviewing items 1 through 3 in the troubleshooting guide for 'Winch will not operate in either direction'. Next, engage the extend on/off control valve (Valve C) manual override while attempting to extend. If the cylinder operates, verify that Valve C is receiving power and then inspect Valve C for contamination.
  • J
    Joseph FosterSep 2, 2025
    What should I do if the lower cylinder on my IMT 5525 Construction Equipment won't extend?
    • S
      Shawn GarciaSep 3, 2025
      If the lower cylinder on your IMT Construction Equipment is not extending, begin by checking items 1 through 3 from the 'Winch will not operate in either direction' troubleshooting steps. Then, engage the lower on/off control valve (Valve D) manual override while operating the function. If the lower operates, verify that Valve D is receiving power and check Valve D for any contamination.
  • S
    Sue HowardSep 5, 2025
    Why is the extend cylinder on my IMT 5525 not retracting?
    • N
      Natasha VasquezSep 5, 2025
      If the extend cylinder on your IMT Construction Equipment is not retracting, refer to items 1 and 2 from the 'Extend cylinder will not extend' troubleshooting guide. Also, check the extend counterbalance valve for contamination.
  • M
    Michael WhiteSep 8, 2025
    Why won't the lower cylinder retract on my IMT 5525?
    • J
      jhowardSep 8, 2025
      If the lower cylinder on your IMT Construction Equipment is not retracting, check items 1 and 2 from the 'Lift cylinder will not extend' troubleshooting guide. Also, inspect the lower counterbalance valve for contamination.
  • D
    Danny HudsonSep 12, 2025
    What to do if my IMT Construction Equipment vehicle tires sink into the ground?
    • M
      Monica MuellerSep 12, 2025
      If the vehicle tires are sinking into the ground, it is likely due to an unstable work area. Reposition the truck to more stable ground, or use blocks under the tires for added support.
  • A
    Anita CooleySep 13, 2025
    Why don't my hydraulic outrigger controls function on my IMT Construction Equipment?
    • D
      Daniel MartinSep 13, 2025
      If the hydraulic outrigger controls aren't working, the crane may not have hydraulic power. Engage the PTO (Power Take-Off) to power the crane’s hydraulic system.

IMT 5525 Specifications

General IconGeneral
BrandIMT
Model5525
CategoryConstruction Equipment
LanguageEnglish

Related product manuals