InFocus IN1503 User Manual

13
Shutting down the projector
The projector automatically displays a black screen after no active source is
detected for 30 minutes. This black screen helps preserve the life of the projector.
The image returns when an active source is detected or a remote or keypad button is
pressed.
Screen Save Time
You can make the black screen appear after a preset number of minutes by turning
on the Screen Save Time feature in the Setup menu. See page 29.
Auto Off Time
The projector also has an Auto Off Time feature that automatically turns the
projector off after no active sources are detected and no user interaction with the
projector is performed for 30 minutes. By default, this feature is off. You can
change the length of time, see page 29.
Turning off the projector
To turn the projector off, press the Power button on the remote or keypad. The lamp
turns off and the LED blinks amber for 1 minute while the fans continue to run to
cool the lamp. When the lamp has cooled, the LED lights amber and the fans stop.
Unplug the power cable to completely power off the projector.
Troubleshooting your setup
If your image appears correctly on the screen, skip to the next section. If it does not,
troubleshoot the setup.
The Status Indicator Panel on top of the projector i
ndicates the state of the projector
and can help you troubleshoot.
Table 3: Status indicator light behavior and meaning
Icon Meaning
Power, solid amber
Power, blinking green
Power, solid green
Power, blinking amber
The projector is plugged in.
The power button has been pressed and the
software is initializing.
The projector
is on and initialized.
The power button has been pressed to turn
the projector
off and the fans are running
to cool the projector.
Thermometer
The projector is too hot. Make sure the
vents aren’t blocked (see page 19). Turn
off the projector and wait one minute, then
turn
the projector on again. Contact
Technical Support if the problem persists.
Visit www.infocus.com/support to contact
service.
Lamp
Turn off the projector and wait one minute,
then turn the projector on again. If the
lamp light turns on again, replace the lamp
and reset the lamp timer.
Wrench/Service
Turn off the projector and wait one minute,
then turn the projector on again. If the
service lamp turns on again, service is
required. Visit www.infocus.com/support
to contact service.

InFocus IN1503 Specifications

General

Matrix size	0.65 \
Native aspect ratio	16:10
Projection distance	0.76/3.51 m
Projection technology	DLP
Supported aspect ratios	4:3, 5:4, 16:9, 16:10
Contrast ratio (typical)	1800:1
Screen size compatibility	- \
Projector native resolution	WXGA (1280x800)
Keystone correction, vertical	-30/30 °
RS-232 ports	0
Focus	Manual
Offset	105 %
Throw ratio	0.72 - 0.86:1
Focal length range	- mm
Lamp power	165 W
Light source type	Lamp
Service life of light source	3000 h
Service life of light source (economic mode)	4000 h
RMS rated power	1 W
Number of built-in speakers	1
Audio (L/R) in	-
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Noise level	29 dB
Power source	AC
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (typical)	170 W
Full HD	No
Supported video modes	1080i, 1080p, 480i, 480p, 576i, 576p, 720p
Analog signal format system	NTSC, PAL, SECAM
Product color	Black

Weight and Dimensions

Depth	222 mm
Width	235 mm
Height	83.8 mm
Weight	2000 g
Package weight	4300 g