InFocus IN24 Reference Guide

14
Shutting down the projector
The projector automatically displays a black screen after no active source is
detected for 30 minutes. This black screen helps preserve the life of the pro-
jector. The image returns when an active source is detected or a remote or
keypad button is pressed.
Screen Save
You can make the black screen appear after a preset number of minutes by
turning on the Screen Save feature in the Settings>System menu. See
page 31.
Power Save
The projector also has a Power Save feature that automatically turns the
lamp off after no active sources are detected and no user interaction with
the projector is performed for 20 minutes. By default, this feature is off. See
page 31.
Turning off the projector
To turn the projector off, press the Power button on the remote or keypad
two times (the second time verifies the shut-down request). The lamp turns
off and the Power light on the Status Indicator Panel blinks green for one (1)
minute while the fans continue to run to cool the lamp. While the light is
blinking green, the projector does not accept any keypad and remote control
input. When the lamp has cooled, the Power light is solid green.
Troubleshooting your setup
If your image appears correctly on the screen, skip to the next section. If it
does not, troubleshoot the setup.
The Status Indicator Panel on top of the projector indicates the state of the
projector and can help you troubleshoot.
Table 2: Status indicator light behavior and meaning
Status Indicator Panel icons Meaning
Power, solid green The power button has been pressed and
the software has initialized or the projec
-
tor has been powered off.
Power, blinking green The power button has been pressed and
the software is initializing, or the projec
-
tor is powering down and the fans are
running to cool the lamp.
Thermometer The projector is too hot. Make sure the
vents aren’t blocked (see
page 20). Turn
off the projector and wait one minute,
then turn the projector on again. Contact
Technical Support if the problem persists
.
Lamp Turn off the projector and wait one
minute, then turn the projector on again.
If the lamp light turns on again, replace the
lamp and reset the lamp timer.
Wrench/Service Turn off the projector and wait one
minute, then turn the projector on again.
If the service lamp turns on again, service
is required. Visit www.infocus.com/service
to contact Service.

InFocus IN24 Specifications

General

Matrix size	0.55 \
Number of colors	16.78 million colors
Native aspect ratio	4:3
Projection distance	- m
Vertical scan range	50 - 85 Hz
Horizontal scan range	15.85 - 85 kHz
Projection technology	DLP
Supported aspect ratios	4:3, 16:9
Contrast ratio (typical)	2000:1
Screen size compatibility	33.6 - 248.4 \
Projector native resolution	SVGA (800x600)
Keystone correction, vertical	25 - 30 °
Projector brightness (economic mode)	1360 ANSI lumens
Lamp type	SHP
Lamp power	200 W
Light source type	Lamp
Lamp power (economic mode)	160 W
Service life of light source	3000 h
3D	-
Full HD	No
Supported video modes	1035i, 1080i, 480i, 480p, 576i, 576p, 720p
Analog signal format system	NTSC, PAL, SECAM
Noise level	35 dB
Plug and Play	Yes
Power source	AC
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	- W
Power consumption (typical)	250 W
Operating temperature (T-T)	10 - 40 °C
Focal length range	- mm
RS-232 ports	0
Maximum analog resolution	1024 x 768 pixels
RMS rated power	1 W
Number of built-in speakers	1
USB connector type	USB Type-B
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Placement	Desktop, Ceiling
Product type	Standard throw projector
Product color	Black, Silver

Weight and Dimensions

Weight	2700 g