EasyManuals Logo

Integra DTR-5.3 Service Manual

Integra DTR-5.3
47 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #2 background imageLoading...
Page #2 background image
AMPLIFIER SECTION
Continuous average power output (FTC)
All channels: 80 W per channel min. RMS at 8 ohm,
2 channels driven from 20 Hz to 20
kHz with no more than 0.08% total
harmonic distortion.
105 W min. RMS at 6 ohm, 2 channels
driven from 1 kHz with no more
than 0.1% total harmonic distortion.
Continuous power output (DIN) 115 W at 6 ohm
Maximum power output (EIAJ) 145 W at 6 ohm
Dynamic power output (stereo) 2 215 W at 3 ohm
2 160 W at 4 ohm
2 95 W at 8 ohm
Total harmonic distortion: 0.08% at rated power
0.08% at 1 W output
IM distortion: 0.08% at rated power
0.08% at 1 W output
Damping factor: 60 at 8 ohm
Input sensitivity and impedance
LINE (CD, TAPE, DVD,
VIDEO 1-4): 200 mV, 47 k ohm
MULTICHANNEL INPUT
(FRONT L/C/R, SURROUND
L/R): 200 mV, 47 k ohm
(SUBWOOFER): 36 mV, 47 k ohm
COAXIAL (DIGITAL): 0.5 Vp-p, 75 ohm
DVD, VIDEO 1, 2, 3, 4: 1 Vp-p, 75 ohm
1 Vp-p, 75 ohm (Y)
0.28 Vp-p, 75 ohm (C)
COMPONENT VIDEO 1, 2: 1 Vp-p, 75 ohm (Y)
0.7 Vp-p, 75 ohm (P
B, PR)
Output level and impedance
Rec out (TAPE, VIDEO 1): 200 mV, 470 ohm
Pre out: 1 V, 470 ohm
VIDEO (VIDEO 1,
MONITOR OUT): 1 Vp-p, 75 ohm
1 Vp-p, 75 ohm (Y)
0.28 p-p, 75 ohm (C)
COMPONENT VIDEO OUT: 1 Vp-p, 75 ohm (Y)
0.7 Vp-p, 75 ohm (PB, PR)
Frequency response: 10 Hz to 100 kHz:+1/-3 dB
(CD in Direct mode)
Tone control
Bass: ±12 dB at 50 Hz
Treble: ±12 dB at 20,000 Hz
Signal-to-noise ratio (stereo)
CD/Tape: 100 dB (IHF A, 0.5 V input)
Muting: -50 dB
TUNER SECTION
FM
Tuning range: 87.5 -108.0 MHz (50-kHz steps)
Usable sensitivity
Mono: 11.2 dBf, 1.0 µV (75 ohm IHF)
0.9 µV (75 ohm DIN)
Stereo: 17.2 dBf, 2.0 µV (75 ohm IHF)
23 µV (75 ohm DIN)
50 dB quieting sensitivity
Mono: 17.2 dBf, 2.0 µV (75 ohm )
Stereo: 37.2 dBf, 20 µV (75 ohm )
Capture ratio: 2.0 dB
Image rejection ratio
40 dB
IF rejection ratio: 90 dB
Signal-to-noise ratio
Mono: 76 dB
Stereo: 70 dB
Alternate channel attenuation: 55 dB
Selectivity: 50 dB (DIN)
AM suppression ratio: 50 dB
Total harmonic distortion
Mono: 0.2%
Stereo: 0.3%
Frequency response: 30 Hz -15 kHz, ±1.0 dB
Stereo separation: 45 dB at 1 kHz
30 dB at 100 Hz - 10 kHz
AM
Tuning range
530 to 1,710 kHz (10-kHz steps)
Usable sensitivity: 30 µV
Image rejection ratio: 40 dB
IF rejection ratio: 40 dB
Signal-to-noise ratio: 40 dB
Total harmonic distortion: 0.7%
GENERAL
Power supply
AC 120 V, 60 Hz
Power consumption
5.5 A
Dimensions (W H D):
17-1/8" 6-7/8" 16-15/16"
Weight
24.3 lbs.
REMOTE CONTROLLER
Transmitter: Infrared
Signal range: Approx. 16 ft., 5 meters
Power supply: Two "AA" batteries (1.5 V 2)
Specifications and features are subject to change without notice.
DTR-5.3
SPECIFICATIONS
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

Other manuals for Integra DTR-5.3

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Integra DTR-5.3 and is the answer not in the manual?

Integra DTR-5.3 Specifications

General IconGeneral
BrandIntegra
ModelDTR-5.3
CategoryReceiver
LanguageEnglish

Related product manuals