Intex 128644GS - User Manual

29 pages

Save Page as PDF

To Next Page

To Next Page

Loading...

Zusammengeführte PDF Datei. Die Originale sind im folgenden Verzeichnis verlinkt. / Merged PDF File. Original files are linked in the following list. / Sloučený soubor PDF.

Originály jsou propojeny v následujícím adresáři. / Egyesített PDF fájl. Az eredetiek a következő könyvtárban találhatók. / Zlúčený súbor PDF. Originály sú prepojené v

nasledujúcom adresári. / Združena datoteka PDF. Izvirniki so povezani v naslednjem imeniku. / Spojena PDF datoteka. Izvornici su povezani u sljedećem imeniku.

128644GS - Krystal Clear sand filter unit SF90220RC

193GS 2

Air Valve For Water Revitalization Set 24

Hydro Aeration Technology 26

Service Center 28

Table of Contents

Questions and Answers

J
Jacob Rogers Jr.Sep 23, 2025
How to fix an Intex 128644GS inlet threaded air connector or air jet valve that's leaking?
- L
  Lisa PenaSep 23, 2025
  If the inlet threaded air connector or air jet valve on your Intex Water Pump is leaking, tighten or reinstall the plunger valve. Ensure the air jet valve is tight and facing up. If the air jet valve internal seal is blocked, turn the pump ON and run for a few seconds, then turn OFF, repeat 3 times. If the air jet valve internal seal is dirty, remove the air jet valve, flush dirt out with water, and replace the valve back.
E
Erica FrazierAug 23, 2025
What to do if Intex 128644GS Water Pump doesn't pump water or flow is very slow?
- A
  Arthur PerezAug 25, 2025
  If your Intex Water Pump filter isn’t pumping water or the flow is very slow, there might be trapped air in the system – release the air according to the operating instructions section. Check for clogs in the inlet or discharge and clear any obstructions. Also, inspect the intake line for air leaks, tightening hose nuts and checking for damage, and ensure the pool water level is adequate. Backwash the filter if the pool is excessively dirty. If the sand media is clogged with dirt, remove about 1” of sand if necessary. Make sure the nozzle is at the upper position of the pool inlet, and the strainer at the lower position of the pool outlet. Remove any pool vacuuming device attached to the system line, if there is crusting or caking on the filtering sand surface.
J
Juan ArellanoAug 25, 2025
Why my Intex 128644GS doesn't work?
- J
  James ParkAug 26, 2025
  If your Intex water pump isn't working, start by checking the water level; ensure it's at the correct level. Next, inspect the strainer screens at the pool inlet for clogs and clean them if necessary. Also, check the intake hose for air leaks by tightening the hose nuts and inspecting the hose for damage. If these steps don't resolve the issue, the motor may be faulty or the impeller jammed.
T
Todd MorenoAug 26, 2025
How to fix Intex Water Pump filter motor that fails to start?
- P
  Patricia WilliamsAug 27, 2025
  If the Intex Water Pump filter motor won't start, ensure the line cord is plugged into a 3-wire outlet protected by a Class A Ground Fault Circuit Interrupter, or RCD. Also, reset the GFCI/RCD circuit breaker; if it repeatedly trips, your electrical system may have a defect, so turn off the breaker and consult an electrician. Finally, the motor may be too hot; let it cool down before restarting.
K
Kathleen LewisAug 27, 2025
What to do if my Intex Water Pump filter doesn't pump water or the flow is very slow?
- T
  Timothy JohnsonAug 27, 2025
  If your Intex Water Pump filter doesn't pump water or the flow is very slow, first release any trapped air (refer to the operating instructions section). Next, clear any obstructions in the intake hose. After that, check for air leaks on the intake line by tightening hose nuts and inspecting for damage, also check the pool water level. If the pool is excessively dirty, backwash the filter. If the sand media is clogged with dirt, remove about 1 inch of sand if necessary. Ensure the nozzle and strainer connections are not reversed. Remove any pool vacuuming device attached to the system line. Finally, ensure the inlet threaded air connector is connected to the pool inlet upper hole.
J
Johnathan MartinSep 16, 2025
What to do if Pressure Gauge doesn't work on Intex 128644GS?
- F
  Frank CainSep 16, 2025
  If the pressure gauge on your Intex water pump isn't working, the inlet of the pressure gauge may be clogged. Try clearing any obstructions in the intake by unscrewing it from the 6-way valve.
T
Tom NelsonSep 13, 2025
How do I stop my Intex 128644GS Water Pump inlet threaded air connector/ air jet valve from leaking?
- D
  Deborah MirandaSep 13, 2025
  To stop a leak from the inlet threaded air connector or air jet valve on your Intex water pump, ensure the plunger valve is well-fitted by tightening or reinstalling it. Also, check that the air jet valve is tight and facing up. If the air jet valve internal seal is blocked, turn the pump ON and run for a few seconds, then turn OFF, repeating this process 3 times. If the internal seal is dirty, remove the air jet valve, flush out any dirt with water, and then replace the valve.
D
dcabreraSep 14, 2025
How to fix a leaking hose on Intex 128644GS Water Pump?
- D
  Daniel SanchezSep 14, 2025
  If a hose on your Intex water pump is leaking, first ensure the hose nut is securely tight; tighten or reinstall it if necessary. Also, verify that the hose connection fitting o-ring or L-shape o-ring is in place and not damaged.
M
Marcus HodgesSep 5, 2025
How to troubleshoot an inaccurate timer or timer that can't be set on my Intex 128644GS?
- K
  Karl WhiteSep 5, 2025
  If the timer on your Intex Water Pump is inaccurate or can't be set, turn off the pump and restart it 5 minutes later. If this doesn't work, reset the timer.
E
Edward HughesSep 3, 2025
How to solve Intex Water Pump timer inaccurate or timer can't be set?
- D
  Donald HernandezSep 3, 2025
  If the timer on your Intex water pump is inaccurate or cannot be set, try turning off the pump and restarting it 5 minutes later. If that doesn't work, re-set the timer.

Intex 128644GS Specifications

General

Brand	Intex
Model	128644GS
Category	Water Pump
Language	English

Related product manuals

Preview: Intex 128352NP

Preview: Intex 128352GN

Intex Easy Set Pools 128122GN

Preview: Intex SF80220-1

Intex SF80220-1

Intex ECO 15110

Intex SF70220-1

Intex SF60220-1

Preview: Intex ECO20110-1

Intex ECO20110-1

Intex ECO15110-1

Preview: Intex SF90220RC-1

Intex SF90220RC-1

Intex PureSpa SSP-H-10-2

Preview: Intex Krystal Clear SX1500

Intex Krystal Clear SX1500