EasyManua.ls Logo

Intex 128352GN - User Manual

Intex 128352GN
54 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Zusammengeführte PDF Datei. Die Originale sind im folgenden Verzeichnis verlinkt. / Merged PDF File. Original files are linked in the following list. / Sloučený soubor PDF.
Originály jsou propojeny v následujícím adresáři. / Egyesített PDF fájl. Az eredetiek a következő könyvtárban találhatók. / Zlúčený súbor PDF. Originály sú prepojené v
nasledujúcom adresári. / Združena datoteka PDF. Izvirniki so povezani v naslednjem imeniku. / Spojena PDF datoteka. Izvornici su povezani u sljedećem imeniku.
128352GN - Frame Pool Set Ultra Quadra 549 x 274 x
132 cm
Above Ground Pool 2
165IO 17
Overview Pool Size vs Pump Running Time 29
193GS 31
Mounting 53
Air Valve For Water Revitalization Set 54

Table of Contents

Questions and Answers

  • M
    Monica IbarraSep 23, 2025
    How to fix an Intex 128352GN inlet threaded air connector or air jet valve that's leaking?
    • J
      Joshua NicholsSep 23, 2025
      If the inlet threaded air connector or air jet valve on your Intex Water Pump is leaking, tighten or reinstall the plunger valve. Ensure the air jet valve is tight and facing up. If the air jet valve internal seal is blocked, turn the pump ON and run for a few seconds, then turn OFF, repeat 3 times. If the air jet valve internal seal is dirty, remove the air jet valve, flush dirt out with water, and replace the valve back.
  • C
    Cynthia PerryAug 23, 2025
    What to do if Intex Water Pump doesn't pump water or flow is very slow?
    • H
      harperalexandraAug 25, 2025
      If your Intex Water Pump filter isn’t pumping water or the flow is very slow, there might be trapped air in the system – release the air according to the operating instructions section. Check for clogs in the inlet or discharge and clear any obstructions. Also, inspect the intake line for air leaks, tightening hose nuts and checking for damage, and ensure the pool water level is adequate. Backwash the filter if the pool is excessively dirty. If the sand media is clogged with dirt, remove about 1” of sand if necessary. Make sure the nozzle is at the upper position of the pool inlet, and the strainer at the lower position of the pool outlet. Remove any pool vacuuming device attached to the system line, if there is crusting or caking on the filtering sand surface.
  • D
    Dale MorganAug 25, 2025
    Why my Intex 128352GN Water Pump doesn't work?
    • D
      Daniel SimonAug 26, 2025
      If your Intex water pump isn't working, start by checking the water level; ensure it's at the correct level. Next, inspect the strainer screens at the pool inlet for clogs and clean them if necessary. Also, check the intake hose for air leaks by tightening the hose nuts and inspecting the hose for damage. If these steps don't resolve the issue, the motor may be faulty or the impeller jammed.
  • G
    gregory40Aug 27, 2025
    How to fix Intex 128352GN Water Pump filter motor that fails to start?
    • V
      Veronica FerrellAug 27, 2025
      If the Intex Water Pump filter motor won't start, ensure the line cord is plugged into a 3-wire outlet protected by a Class A Ground Fault Circuit Interrupter, or RCD. Also, reset the GFCI/RCD circuit breaker; if it repeatedly trips, your electrical system may have a defect, so turn off the breaker and consult an electrician. Finally, the motor may be too hot; let it cool down before restarting.
  • R
    Robert GeorgeAug 27, 2025
    What to do if my Intex 128352GN Water Pump filter doesn't pump water or the flow is very slow?
    • R
      rebeccatranAug 27, 2025
      If your Intex Water Pump filter doesn't pump water or the flow is very slow, first release any trapped air (refer to the operating instructions section). Next, clear any obstructions in the intake hose. After that, check for air leaks on the intake line by tightening hose nuts and inspecting for damage, also check the pool water level. If the pool is excessively dirty, backwash the filter. If the sand media is clogged with dirt, remove about 1 inch of sand if necessary. Ensure the nozzle and strainer connections are not reversed. Remove any pool vacuuming device attached to the system line. Finally, ensure the inlet threaded air connector is connected to the pool inlet upper hole.
  • A
    annealvaradoSep 16, 2025
    What to do if Pressure Gauge doesn't work on Intex Water Pump?
    • W
      wjamesSep 16, 2025
      If the pressure gauge on your Intex water pump isn't working, the inlet of the pressure gauge may be clogged. Try clearing any obstructions in the intake by unscrewing it from the 6-way valve.
  • M
    Mario HolmesSep 13, 2025
    How do I stop my Intex 128352GN inlet threaded air connector/ air jet valve from leaking?
    • S
      Stephanie Clark MDSep 13, 2025
      To stop a leak from the inlet threaded air connector or air jet valve on your Intex water pump, ensure the plunger valve is well-fitted by tightening or reinstalling it. Also, check that the air jet valve is tight and facing up. If the air jet valve internal seal is blocked, turn the pump ON and run for a few seconds, then turn OFF, repeating this process 3 times. If the internal seal is dirty, remove the air jet valve, flush out any dirt with water, and then replace the valve.
  • M
    Melissa PattonSep 14, 2025
    How to fix a leaking hose on Intex 128352GN?
    • T
      Toni ManningSep 15, 2025
      If a hose on your Intex water pump is leaking, first ensure the hose nut is securely tight; tighten or reinstall it if necessary. Also, verify that the hose connection fitting o-ring or L-shape o-ring is in place and not damaged.
  • S
    Scott WilliamsSep 5, 2025
    How to troubleshoot an inaccurate timer or timer that can't be set on my Intex Water Pump?
    • B
      Brandy RussellSep 6, 2025
      If the timer on your Intex Water Pump is inaccurate or can't be set, turn off the pump and restart it 5 minutes later. If this doesn't work, reset the timer.
  • M
    Michael SimmonsSep 3, 2025
    How to solve Intex 128352GN Water Pump timer inaccurate or timer can't be set?
    • A
      Anthony PerezSep 3, 2025
      If the timer on your Intex water pump is inaccurate or cannot be set, try turning off the pump and restarting it 5 minutes later. If that doesn't work, re-set the timer.

Intex 128352GN Specifications

General IconGeneral
BrandIntex
Model128352GN
CategoryWater Pump
LanguageEnglish

Related product manuals