Intex krystal clear 602 User Manual (English)

Questions and Answers:

J
Justin FergusonSep 13, 2025
What to do if Intex Water Pump pool inlet air adaptor / air jet valve leaking?
- E
  Eric BondSep 13, 2025
  If the pool inlet air adapter or air jet valve is leaking on your Intex Water Pump, tighten or reinstall the hose clamps. Tighten the air jet valve, ensuring it faces upwards. Plug in the pump and run it for a few seconds, then unplug; repeat this process three times. Remove the air jet valve, flush out any dirt with water, and replace the valve. If necessary, replace the air jet valve with a new one.
M
Michael GutierrezAug 25, 2025
What to do if my Intex krystal clear 602 doesn't work?
- D
  Debra SmithAug 25, 2025
  Check if the water level is low and fill the pool to the correct level. Also, clean the strainer screens at the pool inlet, as they might be plugged up. Tighten hose clamps and inspect the hose for damage if there's an air leak on the intake hose. Clear any sticks or leaves in the intake hose if the impeller is jammed. Finally, open the release valve at the top of the pump to address an air lock inside the cartridge chamber.
M
maxwellannAug 25, 2025
Why Intex Water Pump filter motor fails to start?
- B
  Brian TorresAug 26, 2025
  If your Intex Water Pump filter motor isn't starting, ensure the filter cord is plugged into a 3-wire outlet protected by a Class A Ground Fault Circuit Interrupter. Also, try resetting the circuit breaker. If it trips repeatedly, there might be an electrical system defect requiring an electrician. Finally, allow the motor to cool down.
J
Jessica WolfeAug 26, 2025
Why Intex Water Pump doesn’t pump water or flow is very slow?
- D
  Danny LopezAug 26, 2025
  If your Intex Water Pump doesn't pump water or the flow is very slow, clear any obstructions in the intake hose by discharging it inside the pool wall. Ensure that hose clamps are tightened, inspect the hoses for any damage and check the pool water level. Replace the cartridge if needed, or clean the cartridge more often. Install the nozzle at the upper position of the pool inlet, and the strainer at the lower position of the pool outlet. Make sure the pool inlet air adaptor is connected to the pool inlet upper fitting.
D
Dr. Jon WestAug 27, 2025
Why Intex Water Pump doesn’t work?
- B
  Brian EnglishAug 27, 2025
  If your Intex Water Pump isn’t working, ensure the pool is filled to the correct water level. Clean the strainer screens at the pool inlet. Tighten the hose clamps and check the hose for damage. Clear any sticks or leaves in the intake hose. Open the release valve at the top of the pump.
Z
Zachary WrightSep 9, 2025
What to do if my Intex krystal clear 602 pool inlet air adaptor / air jet valve is leaking?
- M
  Melinda GibsonSep 9, 2025
  If the pool inlet air adaptor or air jet valve is leaking, first tighten or reinstall the hose clamps, ensuring they are well-fitted. Next, tighten the air jet valve and make sure it’s facing up. If the internal seal is blocked, plug in the pump and run it for a few seconds, then unplug it; repeat this process three times. If the internal seal is dirty, remove the air jet valve, flush out the dirt with water, and replace the valve. If the air jet valve is broken, replace it with a new one.
C
Catherine ShafferSep 7, 2025
What to do if Intex Swimming Pool Pump doesn't pump water or flow is very slow?
- S
  Sabrina McmahonSep 7, 2025
  If your Intex Swimming Pool Pump isn't pumping water or the flow is very slow, it could be due to several reasons. Check for clogged inlet or discharge and clear any obstructions in the intake hose by discharging it inside the pool wall. Look for air leaks on the intake line by tightening hose clamps, inspecting hoses for damage, and ensuring the pool water level is adequate. Also, scale or buildup on the cartridge may be the cause, so replace the cartridge if needed. If the pool is excessively dirty, clean the cartridge more often. Ensure that the nozzle is installed at the upper position of the pool inlet, and the strainer at the lower position of the pool outlet, and that the pool inlet air adaptor is connected to the pool inlet upper fitting.
J
Jacob MorganSep 8, 2025
How to fix air lock in Intex krystal clear 602?
- R
  Richard SanchezSep 8, 2025
  To fix an air lock in your Intex Swimming Pool Pump, open the air release valve, and lift and lower the inlet hose until water starts to flow out of the air release valve, then close the air release valve.
J
Jay RuizSep 2, 2025
What causes the top cover of my Intex krystal clear 602 Swimming Pool Pump to leak and how to fix it?
- M
  Marisa HartSep 2, 2025
  A leaking top cover is often due to a missing O-ring. Remove the cover and check for the O-ring. If the O-ring is in place, ensure the cover or air release valve is tightened manually.
K
Kimberly QuinnAug 31, 2025
Why is my Intex krystal clear 602 not pumping water or the flow is very slow?
- J
  jesuschavezAug 31, 2025
  There might be several reasons: * The inlet or discharge could be clogged. Clear any obstructions in the intake hose by discharging it inside the pool wall. * There could be an air leak on the intake line. Tighten hose clamps and check hoses for damage, and also check the pool water level. * Scale or buildup on the cartridge may be the issue. Replace the cartridge. * The pool might be excessively dirty. Clean the cartridge more often. * The nozzle and strainer connection might be reversed. Install the nozzle at the upper position of the pool inlet and the strainer at the lower position of the pool outlet. * Make sure the pool inlet air adaptor is connected to the pool inlet upper fitting.