EasyManuals Logo

Intex PureSpa SJB-HS-20-1C Owner's Manual

Intex PureSpa SJB-HS-20-1C
43 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #14 background imageLoading...
Page #14 background image
299
A
S AVE THESE INSTRUCTIONS
(299IO) SPA (JET + BUBBLE) ENGLISH 7.5” X 10.3” PANTONE 295U 08/20/2018
English
Page 13
SET UP (continued)
Spa Control Unit Installation
1.
Connect the spa control unit to the spa tub
(see drawing 9)
. Hand-tighten the connectors securely.
Do not use tools to tighten.
CAUTION:
Do not sit, lean, cover or place any objects over the spa control unit.
2.
Attachtheltercartridgehousingassemblytotheinsideofthespatuboutletgrid(marked“B”)
(see
drawing 10)
.
Inatethespatubrstbeforeinstallinglterpumpttings.
3.
Beforellingwithwaterensurethebottomdrainvalvecapsaresecurelyclosedontheinsideandoutside.
4.
Fill the spa tub with freshwater to a level between MIN and MAX marked on the inside of the spa wall. Do
notoverllthespa.Nevermovethespatubwithwaterinsideand/orwiththecontrolbaseattachedtothe
spa as the spa or control base may be damaged.
WARNING:
Never pour water with a temperature higher than 40°C (104°F) into the spa
directly. Itisrecommendedtollthespatubwithlukewarmwaterforquickheatingand
energy saving.
5.
Place the spa cover and spa air bladder (pre-installed in spa cover) over the spa tub, and make sure the
spa cover buckles are locked using the key provided after pulling the buckled straps tight.
IMPORTANT:
Inspect the spa cover regularly for leak, premature wear and tear or deterioration. Never
use a damaged spa cover.
6.
Ensure the spa is plugged into an electrical socket and press the button to turn on the control unit
panelbuttonsrst.Pressthebuttononthecontrolpaneltoactivatetheheater,see“SpaControlUnit
Panel” operation section.
IMPORTANT:
The following conditions will lead to slow water heating:
The ambient temperature is lower than 50ºF (10ºC).
Outdoor wind speed is above 8-12 mph (3.5-5.4 m/s).
The jet function is activated when heating the spa water.
The spa is not properly covered with the spa cover when the water is heating.
Spa Cover
The attachment buckles of the cover are locking buckles. Two keys are provided in the plastic bag with the
manual and other accessories. Each buckle is marked with “locked” and “unlocked” symbols for easy operation:
put the key into the slot on the buckle and turn it to the appropriate position to lock or unlock the buckle
respectively.
To assure safety from unauthorized access, always put the cover on when spa is not in use and lock all
buckles. Always keep the keys out of reach of children. In case you misplace the keys, you can use any similar
sizeatscrewdrivertolockorunlockthebuckles.
When the spa is being used, the cover should be placed in a clean, dry area, otherwise it can pick up dirt and
bacteria. Covers should not be put on wooden tables or wooden decking because of the risk of bleaching the
wood. A cover lifter, dedicated support or similar device, is recommended for ensuring that the cover, mostly its
side facing the water, does not come into contact with the ground or any other dirty surfaces.
10
B
9
40
C
40
C

Other manuals for Intex PureSpa SJB-HS-20-1C

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Intex PureSpa SJB-HS-20-1C and is the answer not in the manual?

Intex PureSpa SJB-HS-20-1C Specifications

General IconGeneral
BrandIntex
ModelPureSpa SJB-HS-20-1C
CategorySwimming Pool
LanguageEnglish

Related product manuals