Intex PureSpa SJB-HS-20-1C User Manual (English)

Other manuals for Intex PureSpa SJB-HS-20-1C

Questions and Answers:

T
Taylor CollinsAug 29, 2025
How to fix an Intex PureSpa SJB-HS-20-1C Swimming Pool that is not heating properly?
- C
  Carolyn BoydAug 29, 2025
  If your Intex Swimming Pool isn't heating properly, first, increase the set temperature and ensure the spa cover is attached. Make sure the filter cartridge is clean; replace it if necessary. If the heater is in STANDBY mode, press the flame button twice to heat the water to the set temperature. If the heating element has failed, further assistance is needed.
M
Maria MooreSep 4, 2025
Why is the filtration pump not working on my Intex Swimming Pool?
- A
  aarondiazSep 4, 2025
  If the filtration pump on your Intex Swimming Pool isn't working, start by cleaning or replacing the filter cartridge. Also, check and clean the filtration inlet and outlet regularly to ensure they are not clogged. If the filter pump motor has failed, contact an Intex Service Center.
T
Tyler AlvarezAug 28, 2025
What to do if the Intex PureSpa SJB-HS-20-1C has no display or the spa control unit does not work?
- N
  Nancy GarciaAug 28, 2025
  If the Intex Swimming Pool's display isn't working or the spa control unit is unresponsive, first, ensure the spa is properly plugged in and switched on. Then, check that the control panel cable plug is firmly attached to the control base receptacle. Also, verify the power source and reset the RCD if it has tripped. If the RCD is broken, further assistance is needed.
L
Laurie Fleming MDSep 13, 2025
What does E90 mean on my Intex Hot Tub?
- C
  Christina RossSep 13, 2025
  To address the E90 error on your Intex Hot Tub, start by turning off and unplugging the control unit. Ensure the outlet cover grid is clean and free from obstructions. Clean or replace the cartridge. Verify that the inlet/outlet connections on the spa tub and filter pump are not blocked. Keep the spa water properly sanitized to ensure a clean and unclogged filter cartridge. Release trapped air by unscrewing the drain valve cap, and then run the filter function. If the problem continues, contact Intex Service Center.
C
Christopher SextonSep 5, 2025
What causes insufficient chlorine in my Intex PureSpa SJB-HS-20-1C Swimming Pool and how to fix it?
- M
  Mark VillaSep 5, 2025
  If there is insufficient chlorine in your Intex Swimming Pool, increase the sanitation system operating time and ensure the heater is off during the sanitation process. Use a spa cover when the spa is not in use or when the sanitation system is operating to prevent chlorine loss due to sunlight. If the bather load has increased, increase the sanitation system operating time and test the water using test strips. Also, check and clean the electrolytic cell if it's clogged or dirty.
K
Kevin ThompsonSep 8, 2025
How do I fix an E90 error on my Intex PureSpa SJB-HS-20-1C?
- L
  Linda MckenzieSep 8, 2025
  If your Intex Swimming Pool displays an E90 error code, turn off and unplug the control unit. Ensure the outlet cover grid is clean and free from obstructions.
J
jtranSep 12, 2025
What to do if my Intex Hot Tub jets output are weak?
- T
  Taylor WoodsSep 12, 2025
  If your Intex Hot Tub jets have weak output: * Add water between the MIN and MAX level. * Ensure the suction inlet is not covered or blocked. * Clean any dirt inside the jet nozzles. If the jet nozzles plumbing pipes are damaged, contact Intex Service Center.
C
Crystal BarberAug 26, 2025
How to clean my Intex PureSpa SJB-HS-20-1C water when it is not clean?
- R
  Ronald BakerAug 26, 2025
  If the water in your Intex Swimming Pool is not clean, ensure the cartridge assembly is properly attached. Insufficient filtering time could be the issue, so increase it. Also, a dirty filter cartridge can cause this, so clean or replace it. Maintain proper water sanitation, following the chemical manufacturer’s instructions, and check and clean the filtration inlet and outlet regularly.
J
Jessica HopkinsAug 25, 2025
How to clean Intex PureSpa SJB-HS-20-1C Swimming Pool water?
- L
  llesterAug 26, 2025
  If the water in your Intex Swimming Pool is not clean, ensure the cartridge assembly is properly attached. Also, increase the filtration time and clean or replace the filter cartridge as needed. Maintain proper water sanitation following the chemical manufacturer’s instructions. Regularly check and clean the filtration inlet and outlet.
M
moorealexandraAug 25, 2025
How to fix Intex Hot Tub error E90?
- P
  Priscilla SolomonAug 25, 2025
  To address the E90 error on your Intex Hot Tub, start by turning off and unplugging the control unit. Ensure the outlet cover grid is clean and free from obstructions. Clean or replace the cartridge. Verify that the inlet/outlet connections on the spa tub and filter pump are not blocked. Keep the spa water properly sanitized to ensure a clean and unclogged filter cartridge. Release trapped air by unscrewing the drain valve cap, and then run the filter function. If the problem continues, contact Intex Service Center.