MAINTENANCE
LI-ION BATTERY
• If camera is not used for a prolonged period of time, the li-ion battery must be recharged periodically
(to full charge at least once a year) to maintain operating ability. Do not allow battery to become total
discharged which can cause it to become non-functional and is not covered under warranty.
• Do not expose the battery (and camera) for prolonged periods of time to temperatures outside the
recommended range of -10°C to 55°C/14°F to 131°F. Exposure to extreme cold or heat can shorten
battery life or damage the battery and is not covered under warranty.
• Do not allow the camera’s internal battery and components to become wet or exposed to high
humidity, etc. which can cause corrosion resulting in damge and is not covered under warranty.
• Do not disassemble camera in order to remove the battery. Damaging, puncturing, shredding, etc.
the battery which can cause an explosion or re. There are no user servicable parts inside the battery
(or camera). Do not use the camera if the battery is damaged.
• Store the battery (and camera) in a cool dry environment.
BATTERY DISPOSAL
• Dispose of the camera and its rechargeable li-ion battery according to local laws. Many localities
require electronics to be recycled. In the USA, please visit https://www.call2recycle.org/ for more
information on recycling locations. Never dispose of a battery in a re because it may explode.
O-RING
• The O-ring on the waterproof housing door must be properly maintained by inspecting and removing
any dirt, dust, sand, hair, debris, etc. before and after use.
• Use a soft lint free cloth moistened with water to clean the O-ring. DO NOT use any solvents such as
alcohol, acetone, etc. to clean the O-ring. This will cause damage and is not covered under warranty.
• Do not remove the O-ring from the door unless it becomes necessary to clean under the O-ring such
as when the housing is accidentally dropped on the ground with the door open and dirt becomes
trapped between the O-ring and the door groove. Repeatedly removing the O-ring can cause it to
become stretched out. This can lead to the O-ring becoming crimped or pinched when the door is
closed and result in ooding and damage to the camera and is not covered under warranty.
• Apply minimal amount of silicone grease to the O-ring only when necessary. Too much silicone grease
applied at one time or a build up of excess silicone grease can lead to leakage and is not covered under
warranty.
• Use only 100% silicone grease made for O-rings. Use only one drop of grease on an applicator swab and
apply it to the surface of the O-ring. The purpose of silicone grease is to lubricate and moisturize the O-ring
to keep it from drying out and cracking and does not function to keep water out of the camera. It is the
O-ring itself that provides the waterproof seal.
• If it becomes necessary to replace the O-ring, please use a proper O-ring tool to remove and replace the
O-ring. Extra O-rings can be ordered by calling 1-888-297-6062 (USA only) or +1-425-285-1111.
CAMERA HOUSING/CAMERA
• The DUB camera housing is waterproof to 200 ft/60 meters but the internal camera is not waterproof.
• Clean the housing after each use by rinsing it in cool clean running water to remove any salt, dirt, sand,
debris, etc. Be sure that the camera is in the housing and the waterproof door is properly closed and
sealed before rinsing.
• Do not use any solvents such as alcohol, acetone, etc. to clean the housing or camera. This will cause
damage and is not covered under warranty.
• Use a soft lint free cloth to dry the housing/camera and store it in a cool dry environment.
• Do not drop, disassemble, crush, puncture, shred, microwave, etc. the camera which can lead to electric
shock. There are no user servicable parts inside the camera. Do not use the camera if it is damaged.
16
DUB
To Next Page
Loading...
