EasyManua.ls Logo

Ip.Access nanoLTE S60 - User Manual

Default Icon
26 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
nanoLTE S60 AP Hardware Installation
NANO_INST_43315 200_0.5

Questions and Answers

  • N
    Natalie MccarthyAug 13, 2025
    Why is my Ip.Access nanoLTE S60 AP unable to reconnect to the NOS?
    • B
      Brent ShannonAug 13, 2025
      If the IPsec parameter is not enabled, ensure that Device.IPsec.Enable is checked. Also, if the SecGW parameter is incorrect, verify the SecGWServer1 configuration.
  • M
    Michael DennisAug 17, 2025
    What to do if my Ip.Access Wireless Access Point has incorrect provisioned values?
    • L
      Lori MarshallAug 17, 2025
      Correct the values in the NOS and then perform a factory reset.
  • N
    Nicholas PayneAug 20, 2025
    What to do if Cell down, service not available on Ip.Access nanoLTE S60?
    • B
      bob94Aug 20, 2025
      Restart the AP or check the connection settings.
  • K
    Kelsey CampbellAug 25, 2025
    Why is the Service LED Red on my Ip.Access Wireless Access Point?
    • B
      Benjamin MartinAug 25, 2025
      The service might not be available because the AP is administratively locked from the NOS. Check the administrative lock status from the NOS.
  • D
    Debra PatrickAug 28, 2025
    What to do if my Ip.Access nanoLTE S60 Wireless Access Point AP unable to validate any certificates and establish an IPsec tunnel?
    • D
      danielmcclainAug 28, 2025
      If the Time parameter is incorrectly configured, check the X_000295_DefaultNTPServer configuration and ensure it is set. If the Security parameter is incorrectly configured, check the X_000295_DefaultCRLServer BaseUrl configuration and ensure it is set.
  • J
    Joseph WareSep 1, 2025
    How to fix Cell locked, service not available on Ip.Access nanoLTE S60?
    • K
      Karen RodriguezSep 1, 2025
      Perform a factory reset.
  • D
    Daniel HaleSep 4, 2025
    What does it mean if the Service LED is flashing Red on my Ip.Access nanoLTE S60 Wireless Access Point?
    • N
      Nicole LopezSep 5, 2025
      A flashing red Service LED indicates an error condition, usually meaning the cell is also down. Check the status of the cell.
  • E
    Eric TuckerSep 8, 2025
    What to do if nanoLTE S60 Ip.Access Wireless Access Point Does Not Power Up?
    • A
      Ashley PetersSep 8, 2025
      Verify the correct power supply is in use and that mains power is available. Also, ensure that PoE or PoE+ is not being used to attempt to power the AP, as it has no effect on the S60 AP.

Ip.Access nanoLTE S60 Specifications

General IconGeneral
CategoryWireless Access Point
ModelnanoLTE S60
Frequency BandsLTE FDD: B1/B3/B7/B8/B20/B28, LTE TDD: B38/B40/B41
Max ThroughputDL: 150 Mbps, UL: 50 Mbps
Power Supply12V DC, 1A
Antenna TypeInternal
Operating Temperature-20°C to +55°C
Interface1 x 10/100 Mbps Ethernet Port, 1 x SIM Card Slot
SecurityWEP, WPA, WPA2, Firewall
ManagementWeb-based GUI, TR-069

Related product manuals