Page 18
ENGLISH
Jandy
®
Pro Series JE Heat Pumps
|
Installation and Operation Manual
1 2 3 4
RED
BLK
YEL
GRN
®
JANDY AquaLink RS
FILTER PUMP OFF
AIR 79°
06/26/04 MON
6:00 PM
EQUIPMENT ON/OFF
ONETOUCH ON/OFF
MENU / HELP
OR
4-Conductor
Wire
Jandy Pro Series JE Heat Pump Power Interface
OPTIONAL
4 3 2 1
RED
BLK
YEL
GRN
RS Power
Center
S1
S2
RESET
SERVICE
TIME OUT
FILTER PUMP
AUX 1
AUX 2
AUX 3
AUX 4
AUX 5
AUX 6
AUX 7
RS6 & RS8 ONLY
RS8 ONLY
HEATER
SOLAR
POOL MODE
SPA MODE
SPA DRAIN
SPA FILL
AUTO
6 5 4 3 2 1
10 9 8 7 6 5 4 3 2 1
4 3 2 1
4 3 2 1
OR
Thu January, 2009 3:03 PM
AquaLink Touch
Menu OneTouch Help Back Status Photos
Power
FILTER
PUMP
SPA
POOL
HEAT
Pool Temp
86º
Air Temp
78º
SPA
HEAT
AUX1
AUX2
AUX3
Other
Devices
On/Off
Do not use this heat pump if any part has
been under water. Immediately call a qualied
service technician to inspect the heater and
replace any part of the control system which
has been under water.
Keep all objects off the top of the heat pump.
Blocking air ow could damage the unit and
may void the warranty.
Be sure that there is water in the pool and that the
surface level is above the skimmer or other inlet of the
pool’s filter system.
With any new pool or spa installation, operate the filter
pump with the heat pump off long enough to completely
clean the water. This will remove any installation
residue from the water.
Clean the filter at the end of this operation before
starting the heat pump. When raising the temperature
of a cold pool, program the time clock to run the pump
continuously.
This lets the filter system and heat pump operate
continuously until the water reaches the temperature
setting on the temperature control. When that happens,
the heat pump will automatically shut off, but the filter
pump will keep running.
Your new Jandy Pro Series JE heat pump is controlled
by an advanced microprocessor based controller that
provides a sophisticated yet simple interface to operate
your heat pump for maximum efficiency and enjoyment
of your pool. To locate the control buttons, see Figure
14.
When the control panel is turned off, the screen displays
.
To enable the pool mode, press
. The associated
left green LED indicator will light and the unit will
display
.
XXX represents the current temperature setting
on the control. The default setting for pool
temperature is 80°F (26°C).
You can change the temperature set point by pressing
the
or button.Repeatedly press the or
button until you reach the desired temperature set
point. After 5 seconds of inactivity, the new set point is
stored in memory.
When the water temperature falls to 1 degree below
the temperature setting
and after a 5 minute delay, the
control will start the heat pump and the associated right
LED will light RED
.
If connected, the Maintain Heat mode allows the heat
pump to monitor the temperature of the water 24 hours
a day by turning the pool pump on and sampling the
water temperature.
A Maintain Temp Relay is required and the feature must
be enabled.
When the water temperature drops below the
programmed temperature set point, the control will start
the heat pump.
To operate in pool mode with the Maintain Heat feature,
press
, then press , press the button
until
is displayed, press the
button.
The associated left green LED indicator will light and
the unit will display
.Change the temperature
set point by pressing the
or button until
the desired set point is displayed. After 5 seconds of
inactivity, the new set point is stored in memory.
To Next Page
Loading...
Need help?
General
