Janome MB-4 User Manual (English)

Other manuals for Janome MB-4

Instruction Manual92 pages

Brochure6 pages

Questions and Answers:

M
Matthew HernandezAug 17, 2025
Why Janome MB-4 Sewing Machine needle thread breaks?
- M
  Michael MedinaAug 17, 2025
  The needle thread may break due to several reasons: * The needle thread is not threaded properly. * The needle thread tension is too tight. * The needle is bent or blunt. * The needle is not inserted properly. * Stitch density is too dense; modify the pattern by using an embroidery software. * Poor quality threads are used; use high quality threads. * The bobbin thread is not threaded properly.
W
wstokesAug 20, 2025
What to do if my Janome MB-4 doesn't run?
- T
  Tom MillerAug 20, 2025
  If your Janome sewing machine doesn't run, here are a few things to check: 1. Ensure the machine is plugged in correctly. 2. Check for jammed threads in the hook or around the take-up lever; remove any jamming threads. 3. If a confirmation or error message is displayed, turn the power off, then on again. 4. If the control system is not working correctly there is no solution mentioned.
D
davislauraAug 22, 2025
Why does my Janome Sewing Machine keep breaking needles?
- H
  hmontgomeryAug 22, 2025
  Your Janome sewing machine needle might be breaking because: * The needle is not inserted properly. * The needle is bent or blunt. * The needle clamp screw is loose. * The needle thread tension is too tight. * Stitch density is too dense; modify the pattern by using embroidery software. * The needle thread is not threaded properly.
C
Charles GriffithAug 25, 2025
Why is my Janome MB-4 so noisy?
- R
  Robert JohnsonAug 26, 2025
  Your Janome sewing machine might be noisy because: * Lint has accumulated in the hook. * The machine runs out of oil.
A
Amy WalkerAug 27, 2025
What to do if my Janome MB-4 does not run?
- O
  Olivia JohnsonAug 27, 2025
  If your Janome Sewing Machine doesn't run, remove any jamming threads, then turn the power off and on again. You may need to follow the message displayed on the screen to turn it off first.
A
Amy WileyAug 30, 2025
What to do if the bobbin thread breaks on my Janome Sewing Machine?
- C
  Christina DunnAug 30, 2025
  If the bobbin thread breaks, try replacing the bobbin or bobbin case.
B
Bridget MitchellSep 1, 2025
What causes skipped stitches on a Janome MB-4 Sewing Machine?
- E
  Elizabeth DavidsonSep 1, 2025
  Skipped stitches on your Janome sewing machine can occur if: * The needle is not inserted properly. * The needle is bent or blunt. * The needle thread is not threaded properly. * The fabric is not stretched tight enough in the hoop.
T
Tracy SuttonSep 4, 2025
Why does the bobbin thread break on my Janome MB-4 Sewing Machine?
- L
  Laura PerezSep 4, 2025
  The bobbin thread may break due to these reasons: * The bobbin thread is not threaded properly. * Lint has accumulated in the hook. * The bobbin is not inserted into the bobbin case properly. * The bobbin or bobbin case has a scratch or nick; replace the bobbin or bobbin case.
W
wattspamelaSep 6, 2025
Why does the thread form loops on my Janome Sewing Machine?
- W
  Walter NewtonSep 6, 2025
  Thread looping can occur if you are not using high-quality thread. Try using a better quality thread.
P
Patrick MartinSep 9, 2025
What to do if embroidery pattern is distorted on Janome MB-4?
- D
  Danielle WatsonSep 9, 2025
  If the embroidery pattern is distorted or not aligned, cut off and remove any tangled threads.