JBL SUB200 - DETAILED SPECIFICATIONS

JBL SUB200 100W Powered Sub/ Plate Amp
LINE VOLTAGE Yes/No Hi/Lo Line Unit Notes
US 120VAC/60Hz Yes 108-132 Vrms
Normal Operation
Asia 100VAC/50Hz Yes 90-110 Vrms
Normal Operation
EU 230VAC/50-60Hz Yes 207-264 Vrms Normal Operation Normal operation, MOMS required
Parameter Specification Unit
QA Test
Limits Conditions Notes
Amp Section
Type (Class AB, D, other) AB AB
N/A 120V System is Class AB
Type (Class AB, D, other) H H
N/A 230V System is Class H
Load Impedance (speaker) 4 Ohms
N/A Nominal
Rated Output Power 120V 100 Watts
85 @ Nominal input voltage
Different output power due to differences
in amp configuration between 120V and
230V
Rated Output Power 230V 105 Watts
100 @ Nominal input voltage
THD@ Rated Power 0.5 %
1 22K filter
THD @ 1 Watt 0.1 %
0.3 22K filter
DC Offset 10 mV-DC
50 @ Speaker Output
Damping factor >100 DF
50
Measured at speaker terminals, Output
power 90 Watts THD 0.1 %
Input Sensitivity
Input Frequency 50 Hz
50 Nominal Freq.
Line Input (L&R) 15 mVrms
±2dB To 1 Watt 1 input driven
LFE Input 9.5 mVrms
±2dB To 1 Watt LFE input driven only
Speaker/Hi Level Input 245 mVrms
±2dB To 1 Watt (-20 dB below Line In)...1 input driven
Signal to Noise
SNR-A-Weighted 90 dBA
85 To Rated power A-Weighting filter
SNR-unweighted 80 dBr
80 To Rated power 22KHz filter
SNR @ 1W-unweighted 65 dBr
60 To 1 Watt 22KHz filter
Residual Noise Floor 1.5 mVrms
2.5
Volume @max, using RMS reading
DMM/VOM (or A/P)
Residual Noise Floor 1
mVrms(max)
2
Volume @max, w/ A/P Swept
Bandpass Measurement (Line freq.+
harmonics)
Input Impedance
Line input L&R , LFE >10 K ohms
N/A Nominal over the audio BW Reference only
Speaker/Hi Level Input 4.7 K ohms
N/A Nominal over the audio BW Reference only
Filters
Low Pass (fixed or variable) fixed --
±2dB
Slope & Q dB/Octave
N/A
Subsonic filter (HPF) Hz
±2dB
Slope & Q dB/Octave
N/A
Limiter (yes/no) YES --
N/A
THD at Max. Output Power N/A --
N/A
Features
LFE Input YES
Functional
BW Limited to 500 Hz, refer to
ECR00031 & AP Curves
Volume pot Taper (lin/log) LOG --
Functional
ATO YES
Functional
Input Configuration
Line In (L,R) L ,R --
Functional RCA inputs: L , R Summed to Mono
Line level in LFE LFE
Functional
Spkr/Hi Level In
(L,R)
L,R --
Functional L R Summed to Mono
Spkr Out: Level out (L,R)Hi
P
L,R
Functional Direct by pass from Speaker in
Signal Sensing (ATO)
Auto-Turn-On (yes/no) YES --
Functional
ATO Input Frequency 50 Hz
Functional
A
TO Level Line Level in (L,R 2 mV
Functional
2mV@50Hz into Line Input w/ 1 ch.
driven
ATO Level Speaker in 40 mV
Functional
SUB200 (SCS200.7sys)
2