List of Figures
P/N 960-100189RA_Rev. A {EDP #148850} © 2009, Japan CashMachine Co., Limited
VEGAâ„¢ Series BankNote Validator
Page
Figure 2-17 VEGA Banknote Validator Operational Flowchart (Part 1 Full Process).2-8
Figure 2-18 VEGA Banknote Validator Operational Flowchart (Part 2 Stack) ...........2-9
Figure 2-19 VEGA Banknote Validator Operational Flowchart (Part 3 Reject) ........2-10
Figure 4-1 Cash Box & Course Path Reversing Guide Cover Removal...................4-1
Figure 4-2 Cash Box Frame Removal......................................................................4-1
Figure 4-3 Upper Assembly Separation (Part 1) ......................................................4-1
Figure 4-4 Upper Assembly Separation (Part 2) ......................................................4-2
Figure 4-5 Front Bezel Removal...............................................................................4-2
Figure 4-6 Flap Positioning Spring Removals ..........................................................4-2
Figure 4-7 Shaft and Flap #1 & #2 Removal ............................................................4-2
Figure 4-8 Flap Lever Arm Reassembly...................................................................4-2
Figure 4-9 Upper Transport Assembly Removal ......................................................4-3
Figure 4-10 Main CPU Board Removal......................................................................4-3
Figure 4-11 Upper Sensor Board Removal ................................................................4-3
Figure 4-12 Base Unit Carrier Removal (Part 1) ........................................................4-3
Figure 4-13 Base Unit Carrier Removal (Part 2) ........................................................4-4
Figure 4-14 Unplug Inter-Assembly Harnesses .........................................................4-4
Figure 4-15 Sub-Circuit Board Removal ....................................................................4-4
Figure 4-16 Gear Box Motor Assembly Removals .....................................................4-4
Figure 4-17 Stacker & Feed Motor Removal..............................................................4-5
Figure 4-18 Sub-Sensor Board Removal ...................................................................4-5
Figure 4-19 Lower Sensor Board Removal................................................................4-5
Figure 4-20 Tension Pulley Unit Removal..................................................................4-5
Figure 4-21 Belt Cover Removal ................................................................................4-6
Figure 4-22 Transport Belt Removals ........................................................................4-6
Figure 4-23 Stacker Unit Removal (Part 1) ................................................................4-6
Figure 4-24 Stacker Unit Removal (Part 2) ................................................................4-6
Figure 4-25 Course Path Reversing Guide Removal .................................................4-6
Figure 4-26 E-Ring, Gear & Clutch Shaft Removal
....................................................4-7
Figure 4-27 Right Stacker Belt Removal ....................................................................4-7
Figure 4-28 Left Stacker Belt Removal ......................................................................4-7
Figure 4-29 Transport Belt Installation .......................................................................4-7
Figure 5-1 VEGA System Wiring Diagram ...............................................................5-1
Figure 6-1 USB Cable Requirement.........................................................................6-1
Figure 6-2 Tool and Harness Connection.................................................................6-1
Figure 6-3 VEGA Port, DIP Switch & LED Indicator Locations ..................................6-2
Figure 6-4 Hardware Wizard Welcome Screen ........................................................6-2
Figure 6-5
Installation Path Selection Screen ..........................................................6-2
Figure 6-6 Install Options Screen.............................................................................6-2
Figure 6-7 Installation Warning Screen ....................................................................6-2
Figure 6-8 Hardware Wizard Completion Screen.....................................................6-3
Figure 6-9 DIP Switch No. 1 Initial Setting ...............................................................6-3
Figure 6-10 UBA Downloader Screen ........................................................................6-3
Figure 6-11 VEGA Software Selection Screen ..........................................................6-3
To Next Page
Loading...
Need help?
General
