IMPORTANT
SAFETY
INSTRUCTIONS
Putting
sewing
systems
into
operation
is prohibited untii it
has
been
ascertained
that
the
sewing
systems
in
which
these
sewing
machines
wiii
be
built into,
have
conformed
with
the
safety
regulations
in
your
country.
Technical
service
for
those
sewing
systems
is
also
prohibited.
1.
Observe
the
basic
safety
measures,
including,
but
not
limited
to
the
following
ones,
whenever
you
use
the
machine.
2.
Read
ail
the
instructions,
including,
but
not
limited
to
this
Instruction Manual before
you
use
the
machine,
in
addition,
keep
this
instruction
Manual
so
that
you
may
read
it
at
anytime
when
necessary.
3.
Use
the
machine
after
it
has
been
ascertained
that
it
conforms
with
safety
rules/standards
valid in
your
country.
4. Ail
safety
devices
must
be
in position
when
the
machine
is
ready
for work
or
in operation.
The
operation
without
the
specified
safety
devices
is
not
allowed.
5. This
machine
shall be
operated
by appropriately-trained
operators.
6. For your personal protection, we recommend that you
wear
safety
glasses.
7. For
the
following,
turn
off
the
power
switch
or
disconnect
the
power
plug
of
the
machine
from
the
receptacle.
7-1 For threading needie(s), looper,
spreader
etc.
and
replacing bobbin.
7-2 For replacing part(s)of needle, presserfoot,throat plate, looper, spreader, feed dog, needle guard, folder,
cloth
guide
etc.
7-3
For
repair
work.
7-4 When leaving
the
working place or when
the
working place is unattended.
7-5 When using clutch motors without applying brake, it
has
to be waited untii
the
motor stopped totally.
8. Ifyou should allow oil,grease, etc. used with the machine and devices to come in contact with your eyesor
skin or swallow any of
such
liquid by mistake, immediately wash thecontacted
areas
and consult a medical
doctor.
9. Tampering withthe liveparts and devices, regardless ofwhether the machine is powered, is prohibited.
10. Repair, remodeling and adjustment works must only be done by appropriately trained technicians or
specially skilled personnel. Onlyspare parts designated by
JUKI
can be used for repairs.
11. General maintenance
and
inspection works have to
t>e
done by appropriately trained personnel.
12.Repair and maintenance works of electrical components shall be conducted by qualified electric
technicians
or
under
the
audit
and
guidance
of specially skilled personnel.
Whenever you find a failure of any of electrical components, immediately
stop
the machine.
13. Beforemakingrepairand maintenanceworks on the machineequipped withpneumatic parts such
as
an air
cylinder,the air compressor has to be detached fromthe machineand the compressed air supply has to be
cut off. Existing residual air pressure after disconnecting the air compressorfrom the machine has to be
expelled.Exceptionsto this are onlyadjustments and performancechecks done byappropriatelytrained
technicians
or
specially
skilled
personnel.
14. Periodically clean the machine throughout the period of use.
15.Grounding the machineis alwaysnecessary forthe
normal
operation ofthe machine. The machinehas to
be operated inan environmentthat is free
from
strong noise sources such as high-frequency welder.
16.Anappropriate powerplug has to
l>e
attached to the machine by electric technicians. Powerplughas to
t>e
connected
to
a
grounded
receptacle.
17.The machine is only allowedto be used for the purpose intended. Other used are not allowed.
18. Remodel or modifythe machine in accordance withthe safety rules/standards whiletaking all the effective
safety measures.
JUKI
assumes no responsibility fordamagecaused by remodeling or modification ofthe
machine.
19. Warning hints are marked with the two shown symbols.
A
Danger
of
injury
to
operator
or
service
staff
A
items
requiring
special
attention
To Next Page
Loading...
