EasyManuals Logo

Juniper JUNOS OS 10.4 User Manual

Juniper JUNOS OS 10.4
200 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #181 background imageLoading...
Page #181 background image
set bridge-domains bd101 vlan-id 101
set bridge-domains bd200 vlan-id 200
set bridge-domains bd300 vlan-id 300
set bridge-domains bd500 vlan-id 500
set bridge-domains bd600 vlan-id 600
Step-by-Step
Procedure
To configure ERP on CS2:
Configure the trunk interface ge-2/0/4 to connect CS2 to CS1 and trunk interface
ge-2/0/8 to connect CS2 to CS1, and configure the family statement as bridge with
a VLAN ID list of 100 through 1000:
1.
[edit interfaces]
user@cs2# set ge-2/0/4 unit 0 family bridge interface-mode trunk
user@cs2# set ge-2/0/4 unit 0 family bridge vlan-id-list 100-1000
user@cs2# set ge-2/0/8 unit 0 family bridge interface-mode trunk
user@cs2# set ge-2/0/8 unit 0 family bridge vlan-id-list 100–1000
2. Enable ERP, specifying the control channels and data channels for ring-1 and ring-2,
and configure ring-2 as the ring protection link owner:
NOTE: Always configure the east-interface statement first, before
configuring the west-interface statement.
[edit protection-group]
user@cs2# set ethernet-ring ring-1 east-interface control-channel ge-2/0/4.0
user@cs2# set ethernet-ring ring-1 east-interface control-channel vlan 100
user@cs2# set ethernet-ring ring-1 west-interface control-channel ge-2/0/8.0
user@cs2# set ethernet-ring ring-1 west-interface control-channel vlan 100
user@cs2# set ethernet-ring ring-2 data-channel vlan [200, 300]
user@cs2# set ethernet-ring ring-2 east-interface control-channel ge-2/0/4.0
user@cs2# set ethernet-ring ring-2 east-interface control-channel vlan 101
user@cs2# set ethernet-ring ring-2 ring-protection-link-owner
user@cs2# set ethernet-ring ring-2 west-interface control-channel ge-2/0/8.0
user@cs2# set ethernet-ring ring-2 west-interface control-channel vlan 101
user@cs2# set ethernet-ring ring-2 west-interface ring-protection-link-end
user@cs2# set ethernet-ring ring-2 data-channel vlan [500, 600]
3. Configure the routing instance, the bridge domains, and the VLAN IDs associated
with each bridge domain:
[edit bridge-domains]
user@cs2# set bd100 vlan-id 100
user@cs2# set bd101 vlan-id 101
user@cs2# set bd200 vlan-id 200
user@cs2# set bd300 vlan-id 300
user@cs2# set bd500 vlan-id 500
user@cs2# set bd600 vlan-id 600
Results Check the results of the configuration:
user@cs2> show configuration
interfaces {
ge-2/0/4 {
unit 0 {
161Copyright © 2012, Juniper Networks, Inc.
Chapter 13: Ethernet Ring Protection

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Juniper JUNOS OS 10.4 and is the answer not in the manual?

Juniper JUNOS OS 10.4 Specifications

General IconGeneral
BrandJuniper
ModelJUNOS OS 10.4
CategoryNetwork Router
LanguageEnglish

Related product manuals