JVC BM-H2000PN User Manual

9-1
10
By
calling
up
the
menu
display
on
screen,
various
functions
can
be
selected
and
set
as
needed.
Calling up the menu display, selecting an item
1. Press the MENU button to call up the menu display on screen (see [1] below).
(Press again to make the display disappear. )
2. Press the & or ¥ button to select an item to be set. “>” is indices for the
selected item.
3. Press the <4 or » button to change the setting.
4, After selecting another item by pressing the A or ¥ button, repeat step 3.
These settings are all kept in memory after power is turned off.
5. Press the MENU button to complete. The menu display disappears.
NOTE
@ When the menu display al) (shown at
left below) is on screen, prass the —
ENTER button. The display changes
to [2] (shown below centre). In this
stata, you can also select the item or
change the setting.
@ Whan the display [Zlis on screen,
each time the ¥ button is prassed
while the ENTER buttan pressed, the
indication moves up or dewn on
screen (the display |3). Press the
MENU button with display [2 (3) or 3]on
screen, and the display is restored to
[Vk
@ifno operation occurs for about 5
minutes: alter galling up the menu
display on: screen, the display
digappenes automaticaly
:NORMAL® |
MENU) a nn |
3 FT
ASPECT
RATIO
4-3
Barc
FLUTER SELECT ;COMB
PEAKING
FREQ.
:2.6MHZ
PEAKING LEVEL :0d8:
» AFC ‘NORMAL
COLOR TEMP. = :6500
NTSC SETUP :0
COMPO. LEVEL ‘SMPTE
<MEMORY MODE>
$8 /COMPO(SDI) . AGB GlAFC -NORMAL@
he | =
LV
[2]
(3]
ASPECT RATIO (picture aspect ratio switching)
The aspect ratio of the picture can be switched between 4:3 and 16:9.
When switching to “16-9” on screen, the height of the picture is slightly
reduced (see right).
ys
the
Bh
lure
in
16:
9
aspect
(ato
ree
FILTER SELECT (built-in filter selection)
When a composite video signal of the NTSC system (excluding NTSC
4.43) is input to the monitor, either or both of two filters in the monitor can be
activated. -
COMB come titer pictures. Ld |
Both: mb and PES | vfiters function at the same time,
| Eliminates dol interference that would show up in the —
vertical boundary’ between two differant. el
"BOTH (both filters)
NOTCH (Trap filter)
@ The function can be operated and the
indication appears only when a
composite video signal of the NTSC
system (exciuding NTSC 4.43) is
input to the monitor.
PEAKING FREQ/JPEAKING LEVEL (picture quality improvement) ——
Corrects the luminance signal to improve picture quality by changing
peak frequency and/or peak level depending on the video signal input to the
monitor. Use PEAKING FREQ. to set correction frequency. Use PEAKING
LEVEL to set correction level.
For component video signal. i:
; 0 a8 to + abs | Set a higher pools for correction to a higher degree.
AFC C (switching of time constant for the AFC)
Use to set the time constant for the AFC (auto fine-frequency control) to
correct skew distortion of video signals input via a videotape recorder or
oinet video equipmen
rr ral- speed correction.
Faster correction.
Slower corer stion.,
COLOR TEMP. (Selon temperature switching)
Use to set the colour temperature of white balance.
NTSC SETUP (NTSC set-up level)
Use to set up the luminance signal level to match the configuration of
the video signal input to the monitor.
- For video signal with 75% luminance signal
COMPO. LEVEL (chrominance level setting)
Use to eet the chrominance abe 4 a COmponenry video signal,
ro sompor nt video Signal rap (atu lever 0%) via a BETACAM
videotape: recorder
BETA75
@ When analogue RGB signals are
input to the moniter, the indications
do not appear and the functions
cannot be operated.
@ By changing the default setting ot
white balance adjustment under the
SET-UP MENU display (see page 15
for adjustment), the + indication is
added te the right of the setting to
indicate that the factory-preset setting
was changed.
«MENU>
ASPECT RATIO :4-3
FILTER SELECT :COMB
PEAKING FREQ. :2.6MHZ
PEAKING LEVEL 76dB
AFC ‘NORMAL
» COLOR TEMP. :6500 *
idol ae A 70
:SMPTE
:RGB
:@
@ The itern and setting are indigated on
seraen and the function can be
operated only when a video signal of
the NTSC system is input to the
moniter.
@ The itarn and setting are indicated on
screen and the furiction can be
operated only when a component
video signal is input to the monitor.
17

JVC BM-H2000PN Specifications

General

Brand	JVC
Model	BM-H2000PN
Category	Monitor
Language	English