JVC BM-H2000PN User Manual

p-l
oh ee
ner oes
aes
as
ote we
@Be sure to turn off aach component's power before connection,
@The connection shown below is only an example. Terminais and their functions differ in accordance with a component te be
connected. Also read and follow the instructions for the component.
|For audio signal input from the
i component connected to VIDEO A IN |
1 For bridge-connected output of 69 i
f Cor audio signal input from the ‘
“ component connected to VIDEO B |
| Component that oulpute a 4)
nat composite video signal
Component that outpuis a 4} '
: - ; 1iCompenent that outputs Y/C signals}
ae Gg
jcomposile video signat
{ Compotiant that outpute | E
|_@aync signal
{For audio signal input from the
: | compenent connected tg
Raa/COMPO(SD) iN:
Component that outpute | | Component that outputs i
[ Remote control |
{ component
analogue AGB signals | _a component signal
Externalinternal synchronisation
Push the front panel EXT SYNC switch to ON, and the monitor operates
to synchronise with an external sync signal input to the rear panel SYNC IN
terminai.
Push the switch again to OFF, and the monitor operates to synchronise
with a sync signal included in a video signal (if it includes a sync signal) input
via a video input terminal.
RGB/COMPO(SDI) terminal setting
PEAKING FREQ. :2.6MHZ
PEAKING LEVEL :0d8
«MENU >
_
;
ASPECT
RATIO
:4-3
Set RGB or COMPO. on screen to match the type of video signal input to FILTER SELECT :COMB
the rear panel RGB/COMPO(SDI) IN terminals.
To
input
analogue
RGB
signals,
set
to
RGB.
AFG
:NORMAL
To
input
Y,
B-Y
or
R-Y
signal,
set
to
COMPO..
NTSC
SETUP
oO
COMPO. LEVEL ‘SMPTE
(MEMORY MODE)
» RGB {/COMPO(SDD :RGB
O& a)
Operation:
1. Press the front panel MENU button to cail up the MENU display on screen.
2. Press the & or W button to select RGB/COMPO(SD)).
3. Press the < or > button to set RGB or COMPO..
4. Press the MENU button to complete.
1. To turn the power on:
Push the POWER switch.
The POWER indicator glows green. The mode and colour system of an input
signal are automatically discerned and displayed on screen for about 3 sec-
onds. To turn off power, push the POWER switch again, and the POWER
indicator goes off.
2. To select the input:
Push an INPUT SELECT switch.
Push VIDEO A, VIDEO B, RGB/COMPO(SDI) or Y/C. The mode and colour
system of a selected input signal are automatically discerned and displayed on
screen for about 3 seconds. —
3. To adjust the audio level:
Turn the VOLUME control to the right to increase the level, or to the left to
decrease the level.
VIDEO A<inputmode |
PAL + Color system |
To demagnetise the picture tube
_ After positioning near the monitor a speaker (non-magnet-
shielded) or other equipment that generates a strong magnetic
field, or after relocating the monitor, colour patches could appear
in the picture due to magnetisation of the picture tube. If this degaussing must be repeated,
occurs,
push
the
DEGAUSS
switch
to
demagnetise
the
picture
proceed
after
at
least
10
minutes
tube.
have
passed
since
first
degaussing.
@The
optional
wireless
remote
control
features
a
DEGAUSS
key.
@This function is not effective if
ac vated a second time after a very
short time has elapsed. When:

JVC BM-H2000PN Specifications

General

Brand	JVC
Model	BM-H2000PN
Category	Monitor
Language	English