Pi e c! iutli 0n!i , i iiiii!i!ii!ii!ii!ii!ii!iiiii i i! i!ii ii!ii!ii!ii!ii!i i ii; ¸ i iiiiiiiiiiiii!ii!ii!ili iii!i i i iiiii!i!ii!ii!ii!ii!ii!iiiii i i iiiiiiiiiiiii!ii!ii!ili iii!i i i iiiiiiiii!ii!iiiiiiiiiiiiiiii i , i iiiiiiiii!iiiiiiiiililiiiii i i i!ii!!iiiiiii!i !i!iiii!ili i i ii !iiiiiiiiiiiiiii!i!!!i!ii ii ¸
InstaiJatJon
. Install ill a place which is level, dry _md neither too hot nor
too cold between 5°C (41°F) and 35°C (95°F).
. Install the System in a location with adequate ventilation to
prevent internal heat buildup ill the System.
. Leave sufficient distance between tile System and tile TV.
. Keep the speakers away from the TV to avoid interference
with TV.
Powersources
. When unplugging the System from the wall outlet, always
pull on the plug, not the AC power cord.
A DO NOT handle the AC power cord with
.gT_O_,t wet hands
Noisture condensation
Moisture may condense on tile lenses inside the System in
the following cases:
, After starting to heat the room
, In a damp room
• If the System is brought directly from a cold to a warm place
Should this occur, the System may malfunction. Ill this case,
leave the System turned on for a few hours until the
moisture evaporates, unplug the AC power cord, then plug
it ill again.
Internalheat
• A cooling tan is monnted on the rear panel to prevent heat
buildup inside the unit.
For safety, observe the following carefully:
. Make sure there is good ventilation around
the unit. Poor ventilation could overheat
I_ and damage tile unit.
• DO NOT block tbe cooling fan and the
ventilation openings or boles. If tbey are
blocked by a newspaper or clotb, etc., tbe !
heat may not be able to get out.
Others
• Should any metallic object or liquid fall into the System,
unplug the AC power cord and consult your dealer before
operating any further.
• If you are not going to operate tile System for aI1extended
period of time, unplug the AC power cord fi'om the wall
outlet.
If anything goes wrong, unplug the AC power cord and
consult your dealer.
To make the explanations in this manual as simple and
easy-to-understand as possible, we have adapted the
following methods:
, Button and control operations are explained in the table
below. In this manual, the operations using the remote
control are mainly explained; however, you can use the
buttons and controls on the main nnit if they have the same
(or similar) name and marks.
• Some related tips and notes are explained later in the
sections "Learning More about This System" and
"Troubleshooting," but not in the santo section
explaining the operations ( _ indicates that the
content has some inlbrmations). If you want to know more
about the functions, or if you have a doubt about the
function, go to these sections and you will find your answer
there.
Indicates that you press the button
briefly.
Indicates that you press the button
briefly and repeatedly until an
option yon want is selected.
Indicates that you press one of the
buttons.
Indicates that you press and hold the
button tier a specified period.
, The number inside the arrow
indicates the period of press (in this
example, 2 seconds).
* If no number is inside the arrow,
press and hold until the entire
procednre is complete or until you
get a result yon want.
Indicates that you turn the control
toward the specified direction(s).
Indicates that this operation is only
possible using the remote control.
Indicates that this operation is only
possible using the buttons and controls on
the main unit.
To Next Page
Loading...
