Adjusting Audio Recording Level
You can select to adjust the audio recording levels
for the two channels (CH1/CH2) manually or
automatically.
.
CH1
INT
INPUT1
INPUT2
AUTO
MANUAL
CH2
INPUT2INPUT1
PEAKINGLCD BRIGHT
CH2CH1
LINE
MIC
MIC
+48V
Manual Adjustment Mode (Manual
Adjustment)
0
Set the [CH1/CH2 AUTO/MANUAL] switch on
the camera recorder to “MANUAL” to enter the
manual adjustment mode, and use the
[CH1]/
[CH2] recording level adjustment knob to set the
recording level.
0
You can adjust the level manually during the
recording, recording standby, and stop modes.
o
When the input channel is set to “INPUT1”/
“INPUT2”
1
Set the [CH1/CH2 AUTO/MANUAL]
selection switch to “MANUAL
” for the
channel to be adjusted manually.
2
Turn the corresponding [CH1]/[CH2]
recording level adjustment knob to adjust
the level.
When [Audio Set] B [Limiter
]
is set to “Off”,
adjust such that the audio level meter does not
light up at -2 dB even for loud sounds.
(A P135 [ Limiter ] )
.
1
/60
F2. 8
AE
±0
ND1
/64
12 :34 :56
ISO
102400
00: 00: 00.00
5 . 6 f t
B 5600
K
4030 20 10 0
4030 20 10
0
-2dB
o
When the input channel is set to “INT
” for
both [CH1] and [CH2]
1
Set the [CH1 AUTO/MANUAL] selection
switch to
“
MANUAL”.
2
Turn the [CH1] recording level adjustment
knob to adjust the level.
When the built-in microphone and the [AUX]
input terminal are used, the recording levels of
[CH1] and [CH2] are interlocked.
This is also effective when the [CH1 AUTO/
MANUAL] selection switch is set to
[CH2].
Memo :
0
Select [Limiter], [AGC
Response],
[AGC Mode],
or [Int. Mic Separation] in the menu to set the
recording audio.
0
If [Limiter] is set to other than “Off”, the limiter
operates according to the value set.
(A P135 [ Limiter ] )
0
For the reference level to be recorded to an SD
card, set [A/V Set]
B [Audio Set] B [Ref. Level]
to “-20dB”, “-18dB”, or “-12dB”. (common for
CH1/CH2)
(A P135 [ Ref. Level ] )
0
The operations of the [CH2]
recording level
adjustment knob and [CH2 AUTO/MANUAL]
selection switch are disabled.
Automatic Adjustment Mode
0
Set the [CH1/CH2 AUTO/MANUAL] selection
switch to
“AUTO
” or the [FULL AUTO] switch to
“ON” to enter Automatic Adjustment mode. The
audio recording level is set automatically
according to the input level.
0
When the [FULL AUTO] switch is set to “ON”,
mode switching with the [CH1/CH2 AUTO/
MANUAL] selection switch is disabled.
Memo :
0
When [A/V Set
]
B [Audio Set] B [Limiter] is set
to “Off” while in the automatic adjustment mode,
the limiter operates at -6dBFS.
(A P135 [ Limiter ] )
0
When
[A/V Set]
B [Audio Set] B [Audio On FULL
AUTO] is set to “SW Set”, you can switch the
audio recording mode with the [CH1/CH2
AUTO/MANUAL] selection switch on the
camera recorder even when the [FULL AUTO]
switch is set to “ON”.
(A P137 [ Audio On FULL AUTO ] )
Audio Recording
75
Shooting
To Next Page
Loading...
