INSTALLATION (IN-DASH MOUNTING)
The following illustration shows a typical installation. If you have any questions or require information
regarding installation kits, consult your JVC car audio dealer or a company supplying kits.
• If you are not sure how to install this unit correctly, have it installed by a qualified technician.
When installing the unit without using the sleeve / ࠝˀՠΈࢮጆೌϰ༬͵ጆ
In a Toyota car for example, first remove the car radio and install the unit in its place.
ᕙΉ(TOYOTA) ԆԾբ ࡛ζ֊ԆԾЂࡖጅç݈અʹጅ༫ʈմڏڄтé
When using the optional stay / ࠝΈᆊނ
Note : When installing the unit on the mounting bracket, make sure to use the 8 mm-long screws. If longer screws are
used, they could damage the unit.
ٍิ : ӕʹጅϯ༫ϚЁࣙʕç՟·8 mmۂڄᒘീéϨ՟·ཫۂڄᒘീç๑ᖢʹጅé
*
3
Not supplied for this unit.
*
3
ʿᎲʹጅಏաé
Screw (option)
ᒘീ·ڄ
Stay (option)
ᆉށ·ڄ
Fire wall
Վػ
Dashboard
ᄭڷػ
Install the unit at an angle of less than 30˚.
અʹጅϯ༫Ϛ˲ؠ30˚ڄԴܾé
2
Bracket*
3
Ёࣙ*
3
Pocket
ڏೋ
Flat type screws (M5
× 8 mm)*
3
Ꮓᒘീ (M5 × 8 mm)*
3
Bracket*
3
Ёࣙ*
3
Flat type screws (M5 × 8 mm)*
3
Ꮓᒘീ (M5 × 8 mm)*
3
Do the required electrical connections.
නмᄔڄྐཔé
*
1
When you stand the unit, be careful not to damage the fuse on the rear.
*
1
৹ʹጅçʮ˻ʿ࠱๑ᖢנ௰ڄۘᎳീé
Bend the appropriate tabs to hold the
sleeve firmly in place.
Ҿᛮጅೋڄߴдçӕࢭጅೋԕ֣Ϛᄭ
ڷػ˖é
*
2
Fit the protrusions outside the unit.
*
2
અߴ௰˜ϯϚʹጅ௰é
Insert the two handles, then pull them
as illustrated so that the unit can be
removed.
ݝ࿌Εçઅղػܓӕ˾ʈ
ᆥç݈ძᗌϙનղώղӕ
˾çʹጅᎲ˃é
Fit the unit into the mounting sleeve by using four corners of the trim plate.
• DO NOT press the panel (shaded in the illustration).
અʹጅ·ࡴԴڄ༫ྟ֣׆ռϯ༫ࢭ˖é
• ʿ࠱ᐅᏫࡒػă࿌ˀڄఀᅬ௰˜Ąé
Caution when installing / ϰ༬ٍิො
ϰ༬༬éׇ֤ϛᄮڸؼ˗
ʓࡒڄ࿌༱ڷΕʄյܓڄϯ༫ദҺéϨسЉᖅçᄔ࠱Љᘕࢭ˔άڄཊçቁώJVC
ԆԾࡖᛏ˜ኀࢭ˔άաᏻ˙༿é
ëϨسʿᇧ׆Ϩщᇧϙϯ༫ʹጅçᏻቁϐڄӑிʆ࢜գϯ༫é
To Next Page
Loading...
