JVC RX-778VBK Instructions

3. Press TEST to check the speaker
output balance.
"TEST TONE L" starts flashing on the
display, and a test tone comes out of the
speakers in the following order:
TEST
_,,TEST TONE L .__TEST TONE C .__TEST TONE R
(Leftfront speaker) (Center speaker) (Right front speaker) |
/
TEST TONE LS. TEST TONE RS_
(Left rear speaker) (Right rear speaker)
Notes:
• Youcanadjustthespeakeroutput/evelswithoutoutputtingthe
test tone
• No test tone comes out of the center speaker when "CENTER
SPK" is set to "NONE" (see page 14)
• No test tone comes out of the rear speakers when "REAR SPK"
is set to "NONE" (see page 14)
• If the TVis turned on and the proper video input is selected on
the TV, the test tone screen wi!l appear on the 7qZ
• Thesignalindicatorsalsolightonthedisplaywhilethetesttone
comes out of the speake_
L: Lights when the test tone comes out of
the left front speaker
C: Lights when the test tone comes out of _ [ RS ]
the center speaker
R: Lights when the test tone comes out of the right front
speake_
RS: Lightswhenthetesttonecomesoutoftherightrear
speake_
LS: Lights when the test tone comes out of the left rear
speake_
4. Adjust the speaker output levels.
• To adjust the center speaker level, press
CNTR /+ (from 10dB to +10 dB).
• To adjust the left rear speaker level, press
REAR•L/+ (from 10 dB to +10 dB).
To adjust the right rear speaker level, press
REAR.R/+ (from 10 dB to +10 dB).
-- CNTR +
C)
-- REAR'L 4"
5. Press TEST again to stop the test tone.
TEST
%
6. Press EFFECT to select an effect EFFECT
level you want.
• Each time you press the button, the effect
-</
level changes as follows:
E DSP EFFECT1 "-_DSP2ECT 2 _DSP EF,F__.._
DSPEFFECT5 DSPEFFECT4
As the number increases, JVC Theater SmTound becomes
stronger.
On the front panel'.
You can also use the buttons on the front panel to adjust the
Surround modes. However, no test tone is available when using the
buttons on the front panel. So, make adjustments while listening to
the sound of the source played back.
1. Press DSP MODE repeatedly until DSPMODE
"THEATER" or "DIG I I
THEATER" appears on the
display;
• When "THEATER" is selected, the PRO LOGIC, DSP, and
THEATER indicators light up on the display.
• When "DIG THEATER" is selected, the DSP and THEATER
indicators light up on the display.
2. Adjust the speaker output levels.
1) Press BALANCE/SURROUND
ADJUST repeatedly until one of the
indications appears on the display.
"CENTER LEVEL":
To adjust the center speaker level.
"REAR L LEVEL":
To adjust the left rear speaker level.
"REAR R LEVEL":
To adjust the right rear speaker level.
2) "lurn MULTI JOG to adjust the
selected speaker output level (from -10
dB to +10 dB).
3) Repeat 1) and 2) to adjust the other
speaker output levels.
SURROUND
ADJUST
3. Adjust the effect level.
1) Press BALANCE/SURROUND
ADJUS [ repeatedly until "DSP
EFFECT" appears on the display.
The display changes to show the current
setting.
2) "lurn MULTI JOG to select the effect
level.
As you turn it, the effect level changes as
follows:
SURROUND
ADJUST
_._.__FECT 1*'-_DSPEFFECT2*'-_DSPEFFECT3*'1
/
DSPEFFECT5",_DSP EFFECT4
As the number increases, JVC Theater SmTound becomes
stronger.
26

JVC RX-778VBK Specifications

General

Brand	JVC
Model	RX-778VBK
Category	Receiver
Language	English