i Operating JVC's Audio/Video Components--
You can operate JVC's audio and video components with this receiver's remote control, since control signals for JVC
components are preset in the remote control
IMPORTANT:
To operate JVC's audio components using this remote control:
• You need to connect JVC audio components through the COMPU
LINK-3 (SYNCHRO)jacks (see page 33) in addition to the
connections using cables with RCA pin plugs (see page 6).
• Aim the remote control directly at the remote sensor on the
receiver.
• If you use the buttons on the front panel or the menu function to
choose a source, the remote control will not operate that source.
_lb operate a source with the remote control, the source must be
selected using source selecting buttons on the remote control.
• _lb operate the cassette deck or MD recorder using the COMPU
LINK remote control system, set the source name correctly. (See
page 12.)
• Refer also to the manuals supplied with your components.
U [,,_ :
C )
c_ @ (X)-(X)
c_@ (E) @
II ! IN IFN_I 15 F_Jl_; O0
fv ¢_Sl
TVVOL CHANNEL VOL /ME
dVC
Check to see if its remote
to the correct position.
control mode selector is set
To operate the audio
system, TVs, and VCRs,
set it to "AUD!Ofi-V/VCR."
Tuner
After pressing FM/AM (with the remote control mode selector set to
AUDIO/TV/VCR ), yet can perform the following operations:
FMIAM: Alternates between FM and AM.
1 - 10, +10: Selects a preset channel number directly.
For channel number 5, press 5.
For channel number 15, press +10, then 5.
For channel number 20, press -710, then 10.
TUNING UP/TUNING DOWN:
"lMnes into stations.
FM MODE/MUTING: Changes the FM reception mode.
Sound control section (Ampfifier)
You can always perform the following operations (with the remote
control mode selector set to "AUDIO/TV/VCR'):
SURROUND ONIOFF:
SURROUND MODE:
Turns on or off'the Sunound modes ......
Dolby Pro Logic and Dolby Digital.
Selects the DSP modes.
After pressing SOUND (with the remote control mode selector set to
"AUDIO/TV/VCR'), you can perform the following operations:
SEA MODE: Changes the SEA modes.
SUBWOOFER - / +: Adjusts the subwoofer output level.
CNTR - I +: Adjusts the center speaker output level.
REARoL - / +: Adjusts the left rear speaker output level.
REARER - I +: Adjusts the right rear speaker output level.
EFFECT: Selects the effect level.
TEST: Turns on or off the test tone output.
Note:
After adjusting sounds, press the corresponding source selecting
button or DISC to operate your target source by using the 10 keys;
otherwise, the 10 keys cannot be used for operating your target
source.
After pressing CD (with the remote control mode selector set to
"AUDIOfI'V7VCR'), you can perform the following operations on
the CD player:
PLAY:
I,_1_1:
STOP:
PAUSE:
1 - 10, +10:
Starts playing.
Returns to the beginning of the current (or previous)
track.
Skips to the beginning of the next track.
Stops playing.
Pauses playing. 'lb release it, press PLAY.
Selects a track number directly.
For track number 5, press 5.
For track number 15, press TI0, then 5.
For track number 20, press TI0, then 10.
For track number 30, press TI0, +10, then 10.
CD plaver-changer
After pressing DISC (with the remote control mode selector set to
"AUDIO/TV/VCI_."), you can perform the following operations on a
CD player-changer:
PLAY:
STOP:
PAUSE:
1 - 6, 7/P:
Starts playing.
Returns to the beginning of the current (or previous)
track.
Skips to the beginning of the next track.
Stops playing.
Pauses playing. '[b release it, press PLAY.
Select the number of a disc installed in a CD player-
changer.
After pressing CD (with the remote control mode selector set to
"AUDIO/TVYVCR'), you can perform the following operations on
the CD player-changer:
1 - 10, +10: Selects a track number directly.
For track number 5, press 5.
For track number 15, press TI0, then 5.
For track number 20, press TI0, then 10.
For track number 30, press TI0, +10, then 10.
41
To Next Page
Loading...
Need help?
General
